C-130H2 Ops Limits
Quiz yourself by thinking what should be in
each of the black spaces below before clicking
on it to display the answer.
Help!
|
|
||||
---|---|---|---|---|---|
STARTING TIT: Max with enrich on (ground) | 100 C
🗑
|
||||
STARTING TIT: Max without enrichment | 200 C
🗑
|
||||
STARTING TIT: Max for air start | 200 C
🗑
|
||||
STARTING TIT: Normal start limits | 750 – 830 C
🗑
|
||||
STARTING TIT: TIT < 720 C: Do what? | write up, see MX
🗑
|
||||
STARTING TIT: TIT 720 – 749 C: | write up, temp controlling check
🗑
|
||||
STARTING TIT: TIT 830 – 850 C: | write up
🗑
|
||||
STARTING TIT: TIT 850 – 965 C: | stop, write up, 1 retry
🗑
|
||||
STARTING TIT: TIT >965 C: | stop, write, and see MX
🗑
|
||||
STARTING TIT: Abnormal torch | stop, write, see MX
🗑
|
||||
STARTING TIT: Engine start cycle (1 on, then) | 1 off, 5 off, 30 off
🗑
|
||||
ENGINE TIT: Normal continuous range | 200 – 1010 C
🗑
|
||||
ENGINE TIT: Takeoff range / time | 1067 - 1083 C / 5 min
🗑
|
||||
ENGINE TIT: Takeoff reduced minimum | 970 C
🗑
|
||||
ENGINE TIT: Military limit / time | 1049 C / 30 min
🗑
|
||||
ENGINE TIT: Climb / max continuous | 1010 C
🗑
|
||||
ENGINE TIT: Acceleration peak limits | >1083 C (5 secs)/1175 C max
🗑
|
||||
ENGINE TIT: Crossover | 820 C +/- 20 C
🗑
|
||||
ENGINE TIT: Normal Limiting | 1083 C
🗑
|
||||
ENGINE TIT: Max downspeed TIT | 850 C
🗑
|
||||
ENGINE TIT: # of thermocouples | 18 (2 elements each)
🗑
|
||||
ENGINE TIT: thermocouple bad – range | 3.5 to 22 C degrees each
🗑
|
||||
ENGINE RPM: Oil pressure / ignition by | 35%
🗑
|
||||
ENGINE RPM: Normal Flight & Takeoff | 98 – 102% +/- 0.5%
🗑
|
||||
ENGINE RPM: Norm flight idle (on ground) | 92.5 – 100.5%
🗑
|
||||
ENGINE RPM: Normal ground idle | 94 - 102%
🗑
|
||||
ENGINE RPM: Max reverse | 96 – 106%
🗑
|
||||
ENGINE RPM: Low speed ground idle | 69 – 75.5%
🗑
|
||||
ENGINE RPM: Ignition Relay on / off | 16% / 65%
🗑
|
||||
ENGINE RPM: Feather on air start if no NTS by | 10%
🗑
|
||||
ENGINE RPM: Air start light off norm/max | 30% / 40% max
🗑
|
||||
ENGINE RPM: Speed sensitive valve actuate | 94%
🗑
|
||||
ENGINE RPM: LSGI range | 9 - 30 deg
🗑
|
||||
ENGINE TORQUE: Oil temp < 0 C | minimum
🗑
|
||||
ENGINE TORQUE: Oil temp 0 to 40 C | 4,500 IN-LBS max
🗑
|
||||
ENGINE TORQUE: Max allowable - takeoff | 19,600 IN-LBS (for 5 min)
🗑
|
||||
ENGINE TORQUE: Max allowable in flight | 19,600 IN-LBS (30 min)
🗑
|
||||
ENGINE TORQUE: Max continuous | 19,600 IN-LBS
🗑
|
||||
ENGINE TORQUE: NTS operates at | -1,260 +/- 600 IN-LBS
🗑
|
||||
ENGINE TORQUE: Torque to decouple | -6,000 IN-LBS
🗑
|
||||
ENGINE TORQUE: Allowable Reverse Differential | 1,000 IN-LBS
🗑
|
||||
THROTTLES: Temp Limiting Range | 0 - 65 degrees
🗑
|
||||
THROTTLES: Temp Controlling Range | 0 - 65 degrees
🗑
|
||||
THROTTLES: LSGI range | 9 - 30 degrees
🗑
|
||||
AC ELECTRICAL: Frequency range | 380-420 cps
🗑
|
||||
AC ELECTRICAL: Voltage range | 110-125 v
🗑
|
||||
AC ELECTRICAL: Max AC load | 1.05
🗑
|
||||
AC ELECTRICAL: APU generator capacity | 40 kva
🗑
|
||||
AC ELECTRICAL: APU generator load | 1.05
🗑
|
||||
AC ELECTRICAL: Gen caution (out) light illuminates | any phase below or equal to 95 for 4 seconds.
🗑
|
||||
AC ELECTRICAL: Bus caution (off) light illuminates | average phase below 96v / any phase below 100v
🗑
|
||||
AC ELECTRICAL: Generator capacity | 40 kva
🗑
|
||||
DC ELECTRICAL: Voltage Range | 25-30v
🗑
|
||||
DC ELECTRICAL: Max DC load | 1.03
🗑
|
||||
DC ELECTRICAL: DC power sources | Battery, 4TRs, Ext
🗑
|
||||
DC ELECTRICAL: Battery voltage norm / min | 24v / 21v
🗑
|
||||
DC ELECTRICAL: AC&EFC inverter power | ESSENTIAL DC
🗑
|
||||
DC ELECTRICAL: Copilot inverter power | ISOLATED DC
🗑
|
||||
PROP DE-ICE & ANTI-ICE: Timing cycle (De-Ice) | 15 sec on / 45 sec off
🗑
|
||||
PROP DE-ICE & ANTI-ICE: Max Ground ops time (De-Ice) | 2 cycles (2 minutes)
🗑
|
||||
PROP DE-ICE & ANTI-ICE: De-Icing amp load range | 65-90 Amps
🗑
|
||||
PROP DE-ICE & ANTI-ICE: Anti-Ice amps | 20 Amps
🗑
|
||||
WINDSHIELD ANTI-ICE: Cold Start Procedure | 5 seconds on, 10 seconds off, until -43 C
🗑
|
||||
WINDSHIELD ANTI-ICE: Max OAT operations | 81 F (27 C)
🗑
|
||||
WINDSHIELD ANTI-ICE: NESA temp / # of windows | 80-100 F / 9
🗑
|
||||
LEADING EDGE ANTI-ICE: Max ground ops time | 30 sec
🗑
|
||||
LEADING EDGE ANTI-ICE: Normal operating range | 75-200 C
🗑
|
||||
LEADING EDGE ANTI-ICE: Overheat range | >200 C
🗑
|
||||
LEADING EDGE ANTI-ICE: Control valve open/close | 158-180 C
🗑
|
||||
LEADING EDGE ANTI-ICE: Norm temp of anti-ice air | 350 C
🗑
|
||||
LEADING EDGE ANTI-ICE: Check leading edge altitude / temp | >5000 ft MSL or < 20 C
🗑
|
||||
FUEL DISTRIBUTION: Inboard / Outboard difference | 500 LBS - 1000 LBS
🗑
|
||||
FUEL DISTRIBUTION: Symmetrical Tank difference | 1000 LBS
🗑
|
||||
FUEL DISTRIBUTION: Wing to Wing difference | 1500 LBS
🗑
|
||||
FUEL DISTRIBUTION: External Tank difference | 1000 LBS
🗑
|
||||
FUEL DISTRIBUTION: Aux Tank difference | No factor
🗑
|
||||
FUEL DISTRIBUTION: Max Effort Fuel Load | 6,200 LBS outboards, 23,500 LBS total in mains
🗑
|
||||
FUEL SYSTEM PRESSURE: Main tank pump pressure | 15 – 24 psi
🗑
|
||||
FUEL SYSTEM PRESSURE: Aux & ext tank pump pressure | 28 – 40 psi
🗑
|
||||
FUEL SYSTEM PRESSURE: Low fuel press light on | 8.5 psi
🗑
|
||||
FUEL SYSTEM PRESSURE: Aux & ext tank empty light | 23 psi
🗑
|
||||
OXYGEN AND LIFE SUPPORT: O2 ports flight deck / total | 6 / 10
🗑
|
||||
OXYGEN AND LIFE SUPPORT: Fully serviced quantity | 25 liters
🗑
|
||||
OXYGEN AND LIFE SUPPORT: Low light on | 2.5 liters on gage
🗑
|
||||
OXYGEN AND LIFE SUPPORT: Press range (no flow) | 270-455 psi
🗑
|
||||
OXYGEN AND LIFE SUPPORT: Press range (continuous) | 270-340 psi
🗑
|
||||
OXYGEN AND LIFE SUPPORT: # of life rafts / capacity | 4 / 20 men
🗑
|
||||
OXYGEN AND LIFE SUPPORT: Fire extinguishers | 4
🗑
|
||||
OXYGEN AND LIFE SUPPORT: Emergency lights illuminate | -2.5g’s or ESS DC off
🗑
|
||||
OXYGEN AND LIFE SUPPORT: # of Emergency exit lights | 8
🗑
|
||||
OXYGEN AND LIFE SUPPORT: Portable oxygen bottles | 4
🗑
|
||||
ENGINE OIL PRESSURE: Max (start & warm-up) | 100 psi
🗑
|
||||
ENGINE OIL PRESSURE: Normal range / allowable flux | 50-60 psi +/- 10 psi
🗑
|
||||
ENGINE OIL PRESSURE: Minimum (LSGI) | <50 psi if normal at 100%
🗑
|
||||
ENGINE OIL PRESSURE: After negative G, monitor engine for | 2 minutes
🗑
|
||||
ENGINE OIL PRESSURE: After negative G, pressure should return within | 10 seconds (if not do ESP)
🗑
|
||||
ENGINE OIL PRESSURE: After negative G, loss of oil when? | 30 to 90 seconds
🗑
|
||||
GEARBOX OIL PRESSURE: Max (start & warm-up) | >250 psi
🗑
|
||||
GEARBOX OIL PRESSURE: Normal range / allowable flux | 150-250 psi +/- 20 psi
🗑
|
||||
GEARBOX OIL PRESSURE: Mission continuation | 130 psi
🗑
|
||||
GEARBOX OIL PRESSURE: Minimum (LSGI) range | 50-250 psi
🗑
|
||||
OIL TEMPERATURE: Max taxi & time | 85-100 C / 30 min
🗑
|
||||
OIL TEMPERATURE: Max in-flight & time | 85-100 C / 5 min
🗑
|
||||
OIL TEMPERATURE: Normal range | 60-85 C
🗑
|
||||
OIL TEMPERATURE: Oil Cooler flaps maintain | 78-82 C
🗑
|
||||
OIL TEMPERATURE: Minimum for takeoff | 40 C and increasing
🗑
|
||||
OIL TEMPERATURE: Minimum (start & warm-up) | -40 C
🗑
|
||||
OIL QUANTITY: Capacity range | 4 to 12 gal
🗑
|
||||
OIL QUANTITY: Expansion space | 7.5 gal
🗑
|
||||
OIL QUANTITY: Low light at | 4 gal
🗑
|
||||
OIL QUANTITY: Allowable burn rate | 1 qt/hr (.25 gal/hr)
🗑
|
||||
HYDRAULICS: Engine Pump Norm/Max | 2900-3200 / 3500psi
🗑
|
||||
HYDRAULICS: Aux & Emergency Norm/ Max | 2900-3300 / 3500psi
🗑
|
||||
HYDRAULICS: Shutdown if pressure over | 3900 psi
🗑
|
||||
HYDRAULICS: RPM for indication | on speed
🗑
|
||||
HYDRAULICS: RPM for norm press | 30 sec after on speed
🗑
|
||||
HYDRAULICS: LSGI minimum press | 2550 psi
🗑
|
||||
HYDRAULICS: Aileron boost pressure | 2050 psi
🗑
|
||||
HYDRAULICS: Low press light on / off | 1000 psi / 1350 psi
🗑
|
||||
HYDRAULICS: Suction boost light on | 20 psi
🗑
|
||||
HYDRAULICS: Norm - 2 brake app left | 2900 - 3200 psi
🗑
|
||||
HYDRAULICS: Norm – 1 brake app left | 2250 psi
🗑
|
||||
HYDRAULICS: Emergency – 1 brake app left | 2900 psi
🗑
|
||||
HYDRAULICS: Emergency accumulator preload | 1000 +/- 100 psi
🗑
|
||||
HYDRAULICS: Utility/Boost/brake preload | 1500 +/- 100 psi
🗑
|
||||
HYDRAULICS: Loss of sys press checklist | <2500 psi
🗑
|
||||
HYDRAULICS: Do not shut off pump if | > 3450
🗑
|
||||
HYDRAULICS: Flaps 0-15: norm/caution | 1100-1400 / 1600 psi
🗑
|
||||
HYDRAULICS: Flaps 15-100: norm/caution. | 2900- 3200/ 3500 psi
🗑
|
||||
HYDRAULICS: Fluid quantity on board | 21 quarts (5 gal)
🗑
|
||||
APU: Normal temp range | 260-650 C
🗑
|
||||
APU: Max EGT | 650 C
🗑
|
||||
APU: Normal RPM range | 95% - 105%
🗑
|
||||
APU: Max RPM | 106%
🗑
|
||||
APU: Stop switch | 110%
🗑
|
||||
APU: Starter cycle | 1 min on, 4 min off
🗑
|
||||
APU: Warm up | 1 minute for bleed air load
🗑
|
||||
APU: Start and operate below | 20,000 MSL
🗑
|
||||
APU: Door open ground / flight | 35 deg / 15 deg
🗑
|
||||
APU: APU fuel burn | Approx 400 lbs/hr
🗑
|
||||
PROPS: Prop brake disengage | 23% or starter app
🗑
|
||||
PROPS: Pitchlock range | 25 - 55 deg
🗑
|
||||
PROPS: Pitchlock RPM | 103%
🗑
|
||||
PROPS: In pitchlock, maintain RPM | 96% - 98%
🗑
|
||||
PROPS: To unlock pitchlock | Increase 2 deg
🗑
|
||||
PROPS: Lo pitch stop blade angle | 23 deg
🗑
|
||||
PROPS: Low pitch stop test | >200 in-lbs increase
🗑
|
||||
PROPS: Prop oil quantity (total) | 26 quarts (6.5 gal)
🗑
|
||||
PROPS: Prop oil sump capacity | 6.5 quarts in press side
🗑
|
||||
PROPS: Prop low oil light on at | 2 quarts low in press side
🗑
|
||||
PROPS: Torque to decouple | -6000 in-lbs
🗑
|
||||
PROPS: Prop aux pump limit | 1 min on, 1 min off, not > 2 min in 30 min
🗑
|
||||
PROPS: Static feather check time (R - F) | 25 sec
🗑
|
||||
PROPS: Pull out if not pop out in | 6 sec
🗑
|
||||
PROPS: Prop fail to feather, hold for | 30 sec
🗑
|
||||
PROPS: NTS operates at | -1,260 +/- 600 in-lbs
🗑
|
||||
PROPS: Blade angle in reverse | -6 to -8 degrees
🗑
|
||||
BLEED AIR: Diffuser air temp/press | 600 F / 125 psi
🗑
|
||||
BLEED AIR: Engine minimum out press (override) | 70 psi
🗑
|
||||
BLEED AIR: Ground check for engine | 65–35 psi >= 16 sec
🗑
|
||||
BLEED AIR: Ground check for APU | 30–15 psi >= 16 sec
🗑
|
||||
BLEED AIR: Regulated output (Norm) | 40 - 50 psi
🗑
|
||||
BLEED AIR: Regulators must be within | 3 psi of each other
🗑
|
||||
PRESSURIZATION: Gauge range | -1.2 to 15.8” Hg
🗑
|
||||
PRESSURIZATION: Safety valve open | < -0.76 & > 15.9” Hg
🗑
|
||||
PRESSURIZATION: Controller nominal press | 15.16” Hg
🗑
|
||||
PRESSURIZATION: Cockpit windshield cracked (1 or 2 panes) | 10” Hg max
🗑
|
||||
PRESSURIZATION: Cargo windshield cracked (1 pane) | 10” Hg max
🗑
|
||||
PRESSURIZATION: Cargo windshield cracked (2 panes) | 0” Hg max
🗑
|
||||
PRESSURIZATION: Rate controller min / max rates | 30-200 / 1600-2900
🗑
|
||||
PRESSURIZATION: Crew door jettison pressure | < 3.1” Hg
🗑
|
||||
PRESSURIZATION: Pressure to open pressure regulator valve | 12 psi
🗑
|
||||
AIRSPEEDS AND ANGLES: Max airspeed (mach) | 0.64 mach
🗑
|
||||
AIRSPEEDS AND ANGLES: T-storm penetration | 65 + power off stall, not to exceed 180 KIAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Windmill Taxi Start | 100 KIAS until 4000 feet / 40%
🗑
|
||||
AIRSPEEDS AND ANGLES: Flaps 10 / 20 / 30 / 40 /50 | 220/210/200/190/180
🗑
|
||||
AIRSPEEDS AND ANGLES: Flaps 60/ 70 / 80 /90 /100 | 165/155/150/145/145
🗑
|
||||
AIRSPEEDS AND ANGLES: Door Only | 185 KIAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Ramp and Door | 150 KIAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Air deflector / troop door | 150 KIAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Lights | 250 KIAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Gear | 165 KIAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Wipers ineffective | 180 KIAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Troop door open / locked | 250 KIAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Crewdoor bailout | 150 KIAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Tire rotation (nose/main) | 139 KGS / 174 KGS
🗑
|
||||
AIRSPEEDS AND ANGLES: Crosswind taxi norm/max | 30 KIAS / 60 KIAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Ditching | 10 + stall w/full flaps
🗑
|
||||
AIRSPEEDS AND ANGLES: Max bank angle | 60 degrees
🗑
|
||||
AIRSPEEDS AND ANGLES: Max bank angle w/flaps | 45 degrees
🗑
|
||||
AIRSPEEDS AND ANGLES: Lowest vertical clearance | 5’ 9” (inboard prop)
🗑
|
||||
AIRSPEEDS AND ANGLES: Max speed w/ 60 degrees nose wheel | 5 KIAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Max turn angle >=20 kgs | 20 degrees max
🗑
|
||||
AIRSPEEDS AND ANGLES: Max speed/angle >= 155,000 lbs | 10 KIAS / 20 degrees
🗑
|
||||
AIRSPEEDS AND ANGLES: Angle of flaps at full | 35 degrees
🗑
|
||||
AIRSPEEDS AND ANGLES: Max reverse best at | 60 to 90 KIAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Hold / Instrument approach entry speed | 170 KIAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Inbound on approach speed | 150 KIAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Air Start with no NTS | 130 KIAS below 5000’
🗑
|
||||
AIRSPEEDS AND ANGLES: Recommend air start speed | 180 KIAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Airspeed for prop malfunction | 150 KTAS
🗑
|
||||
AIRSPEEDS AND ANGLES: Elevator trim tab – electrical stop | 6 degrees down / 25 degrees up
🗑
|
||||
AIRSPEEDS AND ANGLES: Elevator trim tab – mechanical stop | 8 degrees down / 27 degrees up
🗑
|
||||
MISC: Temp for nacelle overheat | 300 F
🗑
|
||||
MISC: Temp for turbine overheat | 700 F
🗑
|
||||
MISC: # of nacelle/turbine overheat sensors | 7 nacelle / 4 turbine
🗑
|
||||
MISC: Acceleration bleed valve open | below 94% RPM
🗑
|
||||
MISC: Gear extension/retraction | 19 seconds or less
🗑
|
||||
MISC: Preheat eng & APU below | -37 C
🗑
|
||||
MISC: Cold WX Ops temperature | <= 0 C (32 F)
🗑
|
||||
MISC: Hot WX Ops temperature | > 35 C (95 F)
🗑
|
||||
MISC: Hot brake peak temperature time | 1 to 5 minutes
🗑
|
||||
MISC: Peak hot temperature in wheel/tire | 20 to 30 min
🗑
|
||||
MISC: Fusible plugs in tire melt | 390 F degrees
🗑
|
||||
MISC: Cold WX Ops: LSGI until oil temp | 0 C degrees or more
🗑
|
||||
MISC: Cold WX Ops: in ground idle until | 40 C degrees oil temp
🗑
|
||||
MISC: Underfloor heat temp | 80 F
🗑
|
||||
MISC: Start: prop rotation time | 5 sec max
🗑
|
||||
MISC: Start: Starter Valve light on in | 5 seconds max (2-3 psi to open)
🗑
|
||||
MISC: Start: Starter Valve light out in | 15 seconds after start release
🗑
|
||||
MISC: Seat inertial reel locks at | 2 to 3 G’s
🗑
|
||||
MISC: Pitot tubes for pilot / copilot | 1 & 3 / 2 & 4
🗑
|
Review the information in the table. When you are ready to quiz yourself you can hide individual columns or the entire table. Then you can click on the empty cells to reveal the answer. Try to recall what will be displayed before clicking the empty cell.
To hide a column, click on the column name.
To hide the entire table, click on the "Hide All" button.
You may also shuffle the rows of the table by clicking on the "Shuffle" button.
Or sort by any of the columns using the down arrow next to any column heading.
If you know all the data on any row, you can temporarily remove it by tapping the trash can to the right of the row.
To hide a column, click on the column name.
To hide the entire table, click on the "Hide All" button.
You may also shuffle the rows of the table by clicking on the "Shuffle" button.
Or sort by any of the columns using the down arrow next to any column heading.
If you know all the data on any row, you can temporarily remove it by tapping the trash can to the right of the row.
Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.
Normal Size Small Size show me how
Normal Size Small Size show me how
Created by:
C130FE
Popular Standardized Tests sets