Cisco
Quiz yourself by thinking what should be in
each of the black spaces below before clicking
on it to display the answer.
Help!
|
|
||||
|---|---|---|---|---|---|
| While performing password recovery on a Cisco router, within how many seconds of power up do you need to press the Break key to put the router into ROMMON mode? | 60 seconds
🗑
|
||||
| Which 2 sets of pins are looped on an RJ-45 T1 loopback plug? | 1&4, and 2&5
🗑
|
||||
| Which 2 sets of pins are looped on an RJ45 56K loopback plug? | 1&7, and 2&8
🗑
|
||||
| Which command can be used to diagnose a network connectivity problem? | Ping
🗑
|
||||
| What is the default speed of a Cisco device console port | 9600
🗑
|
||||
| Which command can be used to obtain serial numbers for router network modules? | show module
🗑
|
||||
| Which router series have a Services PerformanceEngine pre-installed? | 3900 series
🗑
|
||||
| Which memory is used during password recovery procedures to boot a Cisco router? | ROM
🗑
|
||||
| Which port types can be used in large chassis Switch ethernet modules? | GBIC, SFP, RJ45
🗑
|
||||
| Which Catalyst Series switches are fixed interface switches? | 2960,3560,3750
🗑
|
||||
| What information does the "show interface" command display? | encapsulation type, layer 2&3 address
🗑
|
||||
| Which type of memory stores the saved IOS image for a Cisco device? | Flash
🗑
|
||||
| Which IOS commands merge the saved configuration to the running configuration? | copy tftp run, copy start run
🗑
|
||||
| Which commands initiates copying the running configuration of a Cisco device to a TFTP server? | copy running-config tftp
🗑
|
||||
| Which command indicates the amount of memory in a Cisco device? | show version
🗑
|
||||
| What is the command to enter priviledged EXEC mode from user EXEC mode? | enable
🗑
|
||||
| What do you type at the device prompt to get a list of all available commands presented. | ?, or Help
🗑
|
||||
| Which two CLI modes do allow the running configuration to be viewed? | Global config, Privileged EXEC
🗑
|
||||
| When referring to the name 1000BaseT, what does the T stand for? | twisted pair
🗑
|
||||
| Which two of the following statements is true about a router? | divides network into separate broadcast domains, chooses the best route for your data to travel
🗑
|
||||
| What are 3 components of a LAN conenction? | Router, hub, switch
🗑
|
||||
| Which layer of the OSI model defines how data is formatted for transmission and how access to the physical media is controlled? | Data link layer
🗑
|
||||
| What is the speed of a T1 line? | 1.544 Mbps
🗑
|
||||
| Which two pairs are used in a 100BaseT ethernet cable? | 1&2, 3&6
🗑
|
||||
| What is true about a Supervisor Engine Module on a large chassis switch? | The switch cannot function with the Supervisor Engine Module, and orange active LED means the supervisor engine is in standby mode.
🗑
|
||||
| Which command exits the global interface configuration mode to privileged EXEC mode on a Cisco device? | end, or CTRL Z
🗑
|
||||
| Where does the Power On Self Test and bootstrap code reside in a router? | ROM
🗑
|
||||
| Which config is the active configuration of the router or switch at a given time? | running-config
🗑
|
||||
| What command can be used to verify the configuration register setting? | show version
🗑
|
||||
| User EXEC mode prompt | Router>
🗑
|
||||
| Privileged EXEC mode | Router#
🗑
|
||||
| Global Configuration Mode | Router(config)#
🗑
|
||||
| Interface config mode | Router(config-if)$
🗑
|
||||
| What is used to logically separate wireless LANS? | Service set identifier
🗑
|
||||
| What must be on the same channel as the access point connected to the wired LAN? | wireless repeater.
🗑
|
||||
| What is a telephone interface which supplies power, provides dial tone, and generates ringing voltage? | FXS
🗑
|
||||
| What resides on High Density Voice Network Modules and combine WAN interface card and voice interface card functionality? | VWICS
🗑
|
||||
| What tools can be used be used to configure a router or switch through a dial up connection for remote administration? | rolled RJ45 console cable, DB9-RJ45 adapter, DB25 to RJ45 adapter
🗑
|
||||
| What type of Ethernet cable is used between a router and PC? | UTP crossover cable
🗑
|
||||
| What type of Ethernet cable is used between a switch and a PC? | UTP straight thru
🗑
|
||||
| What information is shown in the show ip interface brief command output? | interface type and number, status,layer 3 ip address.
🗑
|
||||
| What are 2 ways to access the Windows Firewall settings on XP SP2 or 3? | Start, CP, Windows firewall and Start,Run, cmd, Firewall.cpl
🗑
|
||||
| What transmission mode has a high potential for collisions? | Half duplex
🗑
|
||||
| What happens if you change the configuration register to 0x2142 then reset the router? | Router will boot from Flash memory without loading the startup config
🗑
|
||||
| What type of cable should be used for the Cisco device console port connection? | RJ45 rollover cable
🗑
|
||||
| From a Windows command prompt, which command displays the local IP address? | ipconfig
🗑
|
||||
| Which physcal layer standards use optical fiber for Gigabit Ethernet? | 1000 Base-LX, 1000 Base SX
🗑
|
||||
| What separates the service providers equipment from the customer's wiring and equipment? | demarcation point
🗑
|
||||
| Devices that put data on the service providers network are called? | data circuit-terminating equipment
🗑
|
||||
| The first three octets (24bit) of the class C IP address are used for? | Network ID
🗑
|
||||
| Layer 2 MAC addresses have no _? | hierarchial structure
🗑
|
||||
| What can be used to separate networks by breaking the network into multiple LAN segments called IP subnets? | Router
🗑
|
||||
| What 3 LEDs are Port Mode LEDs on a fixed interface switch? | Port status,Port speed, Port duplex
🗑
|
||||
| What network module must be installed to make a Catalyst 6500 series switch function? | Supervisor Engine module
🗑
|
||||
| What is the port speed when the color of the port speed LED is solid green? | 100 Mbps
🗑
|
||||
| What type of cable is used from a Switch to a Hub? | RJ45 crossover
🗑
|
||||
| What type of cable is used from a Router to a PC? | RJ45 crossover
🗑
|
||||
| What is the default value of the configuration register? | 0x2102
🗑
|
||||
| What must the boot field on the router be set to for the router to enter ROMMON mode automatically? | 0
🗑
|
||||
| What is the command to enter privilege EXEC mode from the user EXEC mode? | enable
🗑
|
||||
| What is the wiring configuration of an UTP crossover cable? | pin 1 crosses to 3, and pin 2 crosses to 6
🗑
|
||||
| What is used for console port configuration? | line con 0
🗑
|
||||
| The running-config file can be found in which memory? | RAM
🗑
|
||||
| Routers operate at what layer of the OSI model? | 3
🗑
|
||||
| Switches divide a network into separate _? | Collision domains
🗑
|
||||
| What are two functions of a hub | Repeater, amplifier
🗑
|
||||
| Category 5e UTP cables can transmit data at speeds up to | 1000Mbps
🗑
|
||||
| True or false - the more twists a UTP cable has, the better category of the cable. | True
🗑
|
||||
| When using Hyperterminal over a TCP/IP netowrk uses what protocl | Telnet
🗑
|
||||
| What protocol provides terminal like access to a remote computer? | Telnet
🗑
|
||||
| What problem would cause fa 0/0 is up, line protocol is down? | encapsulation type mismatch
🗑
|
||||
| Which layer of the OSI model provides routing function? | Network layer
🗑
|
||||
| What devices might be used to connect a router to the point of presence of the service provider? | Cable modem, dsl modem, CSU/DSU
🗑
|
||||
| Which Cisco IOS command is used to enter the vty line configuration to enable telnet access? | line vty 0 4
🗑
|
||||
| What is a high performance WAN protocol that operates at the physical and data link layers of the OSI model? | Frame Relay
🗑
|
||||
| What can provide diagnostic functions such as loopback testing? | CSU/DSU
🗑
|
||||
| Frame Relay relays packets at which layer of th e OSI model? | 2
🗑
|
||||
| The IP address 172.16.12.4 /26 has what subnet mask? | 255.255.255.192
🗑
|
||||
| How many wires are needed for a PC to successfully send data to another PC using an Ethernet lan cable using RJ45 connectors? | 4
🗑
|
||||
| Which topology uses a central device for point to point connections? | star
🗑
|
||||
| What two layers of the OSI model do the TCP/IP protocols operate at? | network, and transport
🗑
|
||||
| What is the high order bit patten for a Class B network? | 10xxxxxx
🗑
|
||||
| How many layers are in the OSI model? | 7
🗑
|
||||
| What command can be used to load a new version of Cisco IOS software onto a router? | copy tftp flash
🗑
|
||||
| What is unicast traffic? | data traffic that is sent to one device
🗑
|
||||
| What is a layer of the OSI model, but not the TCP/IP protocol stack? | presentation layer
🗑
|
||||
| What protocol routes between different autonomous systems? | EGP
🗑
|
||||
| How many TCP segments flow between two computers to establish a TCP connection? | 3
🗑
|
||||
| What is the high order bit of a Class A network? | 01xxxxxx
🗑
|
||||
| Which layer of the OSI model provides translation of data? | presentation
🗑
|
||||
| What approach eliminates loops when multiple switches are implemented in a network? | spanning tree protocol
🗑
|
||||
| RIP and OSPF are what type of protocols? | Routing
🗑
|
||||
| How many frames can pass through a 24 port hub simultaneously, without causing a collision? | 1
🗑
|
||||
| During path selection - what 3 metrics may be used by routing protocols? | Delay, hop count, bandwidth
🗑
|
||||
| How many frames can pass through a 24 port switch simultaneously, without causing a colision and with full duplex used on all ports? | 24
🗑
|
||||
| How many twisted pairs of wire are typically used in a leased line between two routers? | 4 pair
🗑
|
||||
| What kind of physical interface does a router use to connect to a WAN link? | serial
🗑
|
||||
| What term describes how many bits per second the service provider commits to pass over a single PVC? | CIR
🗑
|
||||
| Ethernet Wires | 1,2,3,6
🗑
|
||||
| Ethernet Crossover | 1&3,2&6
🗑
|
||||
| T1 Crossover | 1&4,2&5
🗑
|
||||
| T1 Wires | 1,2,4,5
🗑
|
||||
| 56K | 1,2,7,8
🗑
|
||||
| 56K loopback | 1&7,2&8
🗑
|
||||
| OSI Level 1 | Physical
🗑
|
||||
| OSI Level 2 | Data Link
🗑
|
||||
| OSI Level 3 | Network
🗑
|
||||
| OSI Level 4 | Transport
🗑
|
||||
| OSI Level 5 | Session
🗑
|
||||
| OSI Level 6 | Presentation
🗑
|
||||
| OSI Level 7 | Application
🗑
|
||||
| Transmits bits from 1 computer to another. Defines how cable is attached to the network and what transmission technique is used | OSI Level 1 - Physical
🗑
|
||||
| Creates logical structure package for data. After sending a frame it waits for acknowledgement. | OSI Level 2 - Data link
🗑
|
||||
| Handles routing of data, adresses messages, translates logical names and addresses into physical. Also determines the route from source to destination. | OSI Level 3 - Network
🗑
|
||||
| Handles error recognition and recovery. It ensures complete data transfer. | OSI Level 4 - Transport
🗑
|
||||
| Allows applications on different computers to establish, use, and end a connection. Regulates which computer transmits, and when and how long it transmits. | OSI Level 5 - Session
🗑
|
||||
| Part of OS that converts incoming and outgoing data from one form to another. Also manages encryption and compression. | OSI Level 6 - Presentation
🗑
|
||||
| Represents the services that directly support applications such as software for file transfers, database access, email, and network games. | OSI Level 7 - Application
🗑
|
Review the information in the table. When you are ready to quiz yourself you can hide individual columns or the entire table. Then you can click on the empty cells to reveal the answer. Try to recall what will be displayed before clicking the empty cell.
To hide a column, click on the column name.
To hide the entire table, click on the "Hide All" button.
You may also shuffle the rows of the table by clicking on the "Shuffle" button.
Or sort by any of the columns using the down arrow next to any column heading.
If you know all the data on any row, you can temporarily remove it by tapping the trash can to the right of the row.
To hide a column, click on the column name.
To hide the entire table, click on the "Hide All" button.
You may also shuffle the rows of the table by clicking on the "Shuffle" button.
Or sort by any of the columns using the down arrow next to any column heading.
If you know all the data on any row, you can temporarily remove it by tapping the trash can to the right of the row.
Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.
Normal Size Small Size show me how
Normal Size Small Size show me how
Created by:
sdsober
Popular Computers sets