Help
Options
Didn't know it?
click below
click below
Knew it?
click below
click below
Don't Know
Remaining cards (0)
Know
retry
shuffle
restart
0:00
Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.
Normal Size Small Size show me how
Normal Size Small Size show me how
Barber tab 3
| Question | Answer |
|---|---|
| To perform a bevel-under effect the blade is positioned behind the section of the hair and moved in: | Curved strokes |
| Loss of hair elasticity or split ends may be caused by: | Excessive air forming |
| Before brushing or combing hair that has been curled with an iron, ensure the hair is: | Completely cooled |
| The two most common braiding methods are the 3-strand overbraid and the: | 3-strand underbraid |
| Which thermal styling tool is used to air form wet hair while using brushes, combs and fingers to create temporary direction and texture changes? | Blow dryer |
| The term used to describe dividing the head into workable areas for the purpose of control is called: | Sectioning |
| In activated texture broken lines with exposed ends are visible on what area of the hair? | Surface |
| What term is not a common type of curvature pincurl? | Skip wave |
| What determines the size of the parting when sculpting hair? | Density |
| The diameter of the tool or pincurl will determine the: | Size of the curl |
| The art of dressing and arranging hair to create temporary changes in the form and texture is known as: | Hair design |
| As a general rule coarse hair should be texturized at least | 1 1/2 inches from the scalp |
| A technique that is performed by gliding the open shears along the surface of the hair to achieve mobility is called: | Slicing |
| What angles best represent low projection (elevation)? | 0 to 30 degrees |
| A design line that is used as a length guide for sculpting graduated, layered and square combination form is referred to as: | Mobile (traveling) |
| The apex refers to what part of the head? | Top |
| Which basic form consist of hair length that progress from shorter in the exterior to longer in the interior and is referred to as a one-length cut? | Solid |
| One oblong followed by a row of pincurls is called: | Ridge curl |
| Sculpting shorter lengths within the form to reduce bulk and create support and mobility is called: | Texturizing |
| Holding the hair 90° from the center one diameter base and having the tool sit on the bottom Parting results from which type of bace control? | Half-off base |
| Which of the following time periods describes how long hair pressing results last? | Until the next shampoo |
| That area below the occipital is referred to as the: | Nape |
| Which base control positions the tool completely off the bottom parting? | Off base |
| What affects the amount of volume, lift, fullness or mass achieved in a hair design? | Base control |
| Taper shears, also known as thinning shears are used on the ends of the hair to: | Reduce bulk |
| The process of designing wet hair into the desired position is referred to as molding or: | Shaping |
| To maintain control of the hair, which of the following hair type should be texturized the greatest distance from the scalp? | Coarse hair |
| What form would result from using 180° angle cut? | Increase layered |
| The area of the strand at the scalp in parting is called the? | Base |
| Which of the following is true about the use of a small brush when designing short hair? | Achieves a curlier design |
| What type of pincurl is used to create fullness and height? | Volume |
| A pin curl with an open circle has the ability to produce which of the following effects? | Wider wave pattern with uniform curls |
| When using electric clippers, the attachment that allows the hair to be sculpted at the same length is the: | Guard |
| The process of drying their hair and then styling it to create a new form is called air forming or: | Blow drying |
| A layered cut or 90° cut is known as: | Uniform layered |
| When sculpting with the razor, all of the following results are achieved except: | Regular alternation of short and long lengths |
| Texturizing reduces balk without: | Shortening the overall length appearance of the hair |
| All of the following are true about using a thermal iron on tinted, white or very fine here except: | Highest iron temperature is used |
| To reduce the potential of hair and scalp damage from heat, hold the blow dryer at least: | 3 to 5 inches from the hair |
| Which tool controls short perimeter lengths when sculpting against the skin? | Taper/contour comb |
| The tool that allows the greatest airflow to the hair while directing it into the lines of the design is called: | Air forming brush |
| Outer boundary or silhouette of any shape or form is known as the: | Form line |
| The type of comb that is used for backcombing and smoothing the surface of the hair is called: | Master sketcher |
| The use of a handheld dryer along with your fingers, brushes, pressing comb and/or a curling iron is called: | Thermal design |
| A weight area in a graduated form could be described as: | Concentration of lengths |
| Which of the following hairstyling products adds shine and weight to the hair? | Pomade |
| The movable blade of the shears is controlled by the: | Thumb grip |
| Projecting the hair below 90° would: | Build weight |
| Distribution begins at the point where motion begins, also known as: | Point of origin |
| Which line is considered to be the artistic pattern or length guide while sculpting hair? | Design line |
Created by:
Lspencer80
Popular Business sets