A+ Networks Word Scramble
|
Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.
Normal Size Small Size show me how
Normal Size Small Size show me how
Question | Answer |
Device that receives a signal on one port and broadcast that signal out to all other ports on the device. | Hub |
Device that receives the signal on one port and uses the MAC Address to only send the signal to the target devices port. | Switch |
Half-Duplex network device. | Hub |
Full-Duplex network device. | Switch |
Devices used to bridge two different network media. | Bridge |
On a 10BaseT network, what does the number stand for? | Bandwidth - 10 MBps |
On a 10BaseT network, what does the letter T stand for? | Cable Type - Twister Pair |
On a 1000BaseCx network, what does the letters CX stand for? | A special cable type typically used in network closets. |
On a typical network, what is the max cable length (meters)? | 100 |
What cable type is used for a 10BaseT network? | Cat3 |
What cable type is used for a 100BaseT network? | Cat5 |
What cable type is used for a 1000BaseT network? | Cat5 |
What cable type is used for a 10GBaseT network? | Cat5e or higher |
What cable type is used for network ending in a letter other than T or C i.e. 1000BaseL? | Fiber Optics |
What is the max length of a fiber optics cable? | 100 meters to 40 kilometers |
Device that connects two network segments that have a different subnet address. | Router |
A router uses this to move data between devices. | IP Address |
A Hub uses this to move data between devices. | None. Sends data received to all ports. |
A switch uses this to move data between devices. | MAC Address |
What is the designation for Fast Ethernet? | 100BaseTx |
What must be configured to send data to a computer on another subnet? | Default Gateway |
How many IP address will a router have? | One for each network interface port |
What resolves names to IP Addresses? | DNS |
What server will automatically provide IP configuration to a client PC? | DHCP |
If a client PC cannot locate the DHCP Server, what method will the PC use to configure the PC's IP address and subnet mask? | APIPA |
What method would be used as a fail safe if a manual Static method , and/or DHCP method failed? | APIPA |
If an the DHCP Address cannot be contacted, what IP Address is returned by APIPA when automatically assigning an address? | 169.254.X.X |
This allows assigning a single IP Address to a network or subnet? | NAT |
What does PAT do? | Assigns a port number to the public IP Address of the Router when NAT is enabled to allow communication back to the specific client. |
List the first range of IP Addresses for a Private Network. | 10.0.0.0 - 10.255.255.255 |
List the second range of IP Addresses for a Private Network. | 172.16.0.0 - 172.31.255.255 |
List the third range of IP Addresses for a Private Network. | 192.168.0.0 - 192.168.255.255 |
What command would you use to obtain the network adapters IP Address, Subnet, and Default Gateway? | ipconfig |
What command would you use to obtain the network adapters IP Address and DHCP Server IP? | ipconfig /all |
What command would you use to release the IP configuration obtained from the DHCP Server? | ipconfig /release |
What command would you use to renew the IP configuration obtained from the DHCP Server? | ipconfig /renew |
What command would you use to send an ICMP echo request to a remote host? | ping |
What command would you use to check connectivity to another device on a Windows computer? | tracert |
What command would you use to look up the IP Address of a host? | nslookup |
What command would you use to get info on the local routing table? | netstat |
Created by:
drward@myway.com
Popular Computers sets