B-General Building 3 Word Scramble
|
Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.
Normal Size Small Size show me how
Normal Size Small Size show me how
| Question | Answer |
| In order for a Nail to properly join two pieces of wood, ____________ of the nail must drive into the base | 2/3rds |
| In order to seal the bottom of a sill plate, it is sometimes required to use a | Sill Gasket Membrane |
| Joints in a double top plate should be offset with joints in the top plate by a minimum of | 4 feet |
| How tall must a Foundation cripple wall be to not require SOLID backing? | 14 inches |
| Any Habitable space should have a minimum ceiling height of | 7 feet |
| Any Habitable room (except kitchens) should have a minimum square feet of | 70 square feet |
| Every dwelling unit should have at least ONE room that is at least _______ square feet | 120 |
| What part of a Floor or Ceiling Joist may NOT be cut or notched | the middle 1/3 |
| A Girder must be pressure treated if it is within _______ of the ground | 12 inches |
| A Floor Joist must be pressure treated if it is within _______ of the ground | 18 inches |
| The post bottoms supporting the girders must be pressure treated if they are within _______ of the ground | 6 inches |
| Floor Joists must lap at least _______ on top of any wall, beam, or girder | 3 inches |
| What are the requirements for under floor ventilation in a crawl space? | 1 sq feet of venting per 150 sq feet of floor area |
| How large must the access hole be for the crawl space? | 18" x 24" |
| Standard nailing schedule for sub-floor? | 6 inches O.C on sides/ 12 inches O.c in field |
| All plywood sub-flooring must have SOLID backing unless you use | T& G |
| What is the maximum amount of notch in a joist? | 1/4 of the depth of the joist |
| When drilling a hole through a joist, the hole may not be within _____ of the top or bottom | 2 inches |
| When drilling a hole through a stud, the hole may not be within _______ of the edge | 5/8 inches |
| A bored hole through the weight bearing stud can be no more than ________ of the stud depth | 40% |
| A bored hole through a non-bearing stud can be no more than _______ of the stud depth | 60% |
| Private stairways must be at least ________ wide | 36 inches |
| A handrail can impinge on the stairway width by no more than | 4.5 inches |
| What is the lowest allowed rise and the highest allowed rise on a private staircase | 4 inches-7 3/4 inches |
| What is the lowest allowed run for a private staircase | 10 inches |
| What is the lowest allowed run for a private staircase without nosing | 11 inches |
| The largest tread width or riser will not exceed the smallest by more than ________ on a staircase | 3/8 inch |
| What size nosings are allowed on a staircase? | 3/4 inch - 1 1/4 inch |
| Open risers are allowed ONLY if a _______ cannot fit through the openings | 4 inch sphere |
| What is the minimum headroom clearance at any point on a stair way | 6 foot 8 inches |
| Which 2 places require 1-hour fire rated construction | Garages and under stair-ways |
| The main external stairway door must have a landing outside. The landing must be ______ | as wide as the door and at least 36 inches long |
| Stairways in a dwelling unit MUST have handrails if over _______ risers are present | 4 |
| What is the minimum clearance between the handrail and wall | 1 1/2" |
| How high above the stair tread nosing must a handrail be installed? | 34 to 38 inches |
| What are the allowed stair handrail diameters? | 1 1/4"-2" |
| What are the requirements for non circular stair handrails? | 4-6 1/4" perimeter with no more than 2 1/4" cross section |
| Any open sides of stairways, landings, balconies, decks etc. more than _______ above grade require gaurdrails | 30 inches |
| The tops of guardrails must be at least _______ above the standing surface | 42 inches |
| No where on a gaurdrail may a _________ pass through any opening | 4 inch sphere |
| A guardrail over a staircase needs to meet which requirements? | 42 inches from standing surface, 4 3/8" sphere cant pass through vertical guards, 6" sphere cant pass through bottom gaurds |
| A roof with two different slopes (one steep one shallow) is known as a | Gambrel Roof |
| The maximum workable slope on a roof is _____ | 8:12 |
| Flat roofs are known as roofs with a pitch of ______ | 2:12 or less |
| a Roof with a steep slope is also known as a | Mansard Roof |
| What must be used to attach rafters to the ridge boards? | Gusset plates or comparable hardware, Nails are not allowed |
| Define Purlins | They run perpendicular to the rafters and are braced to walls or beams below |
| How often must a Purlin be braced? | 4 feet O.C |
| When must a Purlin brace be a 4x4? | When the length is over 6 feet |
| What is the longest you can make a Purlin brace? | 8 feet |
| What are the requirements for Roof Ventilation? | 1 square feet of opening for every 150 square feet of roof |
| What can I use to set rafters without cutting birdsmouths? | VPA connectors |
| Metal roof panels which can be installed over open-frame sheathing is known as | Structural Metal Roof panels |
| Double Top Plates should be nailed together with _________ | 16d every 24 inches |
| Attic Openings should be ________ | 20 " x 30" |
| The attic area directly above the attic opening should have | 30 inches of head room |
| A roof with 3:12 pitch or greater and joinst 16" O.C. should have OSB plywood at least ________ | 15/32" |
| Define a "single ply" roof | Membrane Roofing System (paper, shingles) |
| When framing walls, what is an acceptable variation in heighths? | 1/2" |
| U-Shaped Kitchens should have at least __________ between opposing cabinets and countertops | 60 inches |
| Walk through Kitchens should have at least ________ between oppopsing cabinets and countertops | 40 inches |
| When applying shingles on a roof with a slope LESS than 4:12, what type of paper must be used? | #30 felt |
| Diagonal Bracing with steel or 1x4 must be at a ________ angle | 45 to 60 degree |
| define a "prowl" | It's the part of a roof that is kicked out with outriggers and fascia |
| load bearing joists cannot cantilever more than ___________ | 1x the depth of the joist |
| BUR and single-ply shall not be applied on roof slopes less than | 1/4 : 12 |
| Ceiling Joists on top of a 24" spaced wall cannot be more than __________ from a stud | 5" |
| Modified Bitumen roofing is also known as ____________ | Torch Down |
| Usually, Deck Joists can cantilever ___________ | 1/4x the supported length |
| How long will a 2x4 give fire protection? | 1 hour |
| A floor joist can cantilever ____________ | 4x the joist height |
| OSB on a non-flat roof with 24" O.C Joists should be | 5/8 inch |
| Define a BUR (Built-Up Roof) | multiple layers of room laminated with Asphalt Bitumen or "Torch Down" |
| What type of felt do you need on a shake roof with a 4:12 pitch or more ? | #30 asphalt |
| What is the minimum slope of a tile roof? | 2 1/2 : 12 |
| What type of lumber is used in trusses? | No. 1 structural lumber |
| Define an "out-rigger rafter" | A rafter going off of a hip running perpendicular to the common rafters |
| What size plywood should be used on a wall with 24" O.C studs | 3/8 |
| What size plywood should be used on a wall with 16" O.C studs | 5/16 |
| What are the rules to how holes should be spaced in an I-Joist | they should be spaced by 2x the diameter of the largest hole |
| What is a Hog Valley? | they form when two slopes together |
| A standard fire rated door will burn for | 20 minutes |
Created by:
yobryan2009
Popular Human Services sets