Volume 1. Aircraft Maintenance General Subjects
Quiz yourself by thinking what should be in
each of the black spaces below before clicking
on it to display the answer.
Help!
|
|
||||
---|---|---|---|---|---|
The estimated percent of accidents caused by nature is | 2%
🗑
|
||||
The safety training phase described as an effective tool that creates a lasting impression for new airmen is | initial
🗑
|
||||
The responsibility for initiating a lost tool report belongs to the | person issued the tool
🗑
|
||||
The lowest person authorized to clear a red X when a lost tool cannot be located is the | maintenance superintendent
🗑
|
||||
The optimum temperature to cool sealants mixed in an automatic mixing machine is | 70*F
🗑
|
||||
Temporary storage of hazardous materials at a central accumulation point cannot extend | 90 days
🗑
|
||||
Hazardous Waste Management System Rules are published by | the EPA
🗑
|
||||
Radiation hazards are affected by | strength of emission, time of exposure, and weather
🗑
|
||||
Normally, the safe distance behind an operating jet engine exhaust is | 200 feet
🗑
|
||||
The noise intensity of a jet engine is greatest toward the rear at | 45* angle at either side
🗑
|
||||
They symptom that is not a sign of noise fatigue is: -dizziness -emotional irritability -a feeling of emptiness -impairment of mental concentration | a feeling of emptiness
🗑
|
||||
A fire extinguisher's pressure is within a safe operating range when the gauge needle is within what color markings? | Green
🗑
|
||||
Aircraft oxygen servicing or draining is prohibited within how many feet of hangars or structures? | 50
🗑
|
||||
Individuals not directly involved in nitrogen servicing should be outside how many foot radius | 20 foot radius
🗑
|
||||
Under ideal conditions, an aircraft is said to be operationally ready when? | the required inspection and servicing are complete
🗑
|
||||
As fireguard, position yourself even with the | nose of the aircraft and at a 45* angle outboard of the engine being started
🗑
|
||||
The condition most likely to cause aircraft damage is | sudden local storms
🗑
|
||||
If no maximum wind velocity is specified in the aircraft technical order, the maximum wind velocity as prescribed by Air Force Occupational Safety and Health Standard 91-100, allowed during jacking is | 15 mph
🗑
|
||||
During desert operations, lubrication should be done | only when necessary, and then sparingly
🗑
|
||||
The F-2 lifting bag is designed to lift | 24000 pounds to a maximum height of 6'
🗑
|
||||
A major drawback of using pneumatic lifting bags is | instability
🗑
|
||||
The method of aircraft hoisting confined to emergencies when no other method is available is | crane hoisting
🗑
|
||||
The type of technical order library that does not need to maintain its currency is | reference
🗑
|
||||
In the second grouping of a TO number, the alpha character in parentheses means the | modified aircraft mission
🗑
|
||||
The total number of Air Force TO catalogs is | one
🗑
|
||||
The directional flow of the schematics in the troubleshooting manual is from the | left side of the diagram to the right side of the diagram
🗑
|
||||
Inspection workcards are known as | abbreviated TO
🗑
|
||||
Due to their potential for harm, commanders are required to ensure immediate action TCTO are distributed to all affected personnel within | 4 hours after receipt
🗑
|
||||
The type of TO improvement issued for all TCTO deficiencies is | urgent
🗑
|
||||
The nondirective publication that may cite forms and provide guidance on completing them, but can't enforce what's on the form is | pamphlet
🗑
|
||||
In order of increasing capability, the Air Force's varying degrees of maintenance capabilities are | organizational, intermediate, or depot
🗑
|
||||
The type of maintenance that ensures equipment is ready and available at the time of need is | preventative
🗑
|
||||
The most common excuse for taking short cuts is | time restraints
🗑
|
||||
The prime contributors to dropped objects are | latches and fasteners
🗑
|
||||
In most units, the responsibility for investigating dropped objects rests with | quality assurance
🗑
|
||||
The first step in developing an effective FOD prevention program is to | identify all possible sources of FOD
🗑
|
||||
The responsibility for FOD prevention belongs to | everyone
🗑
|
||||
The method that cannot be used to search for lost tools is | lost particle
🗑
|
||||
The information that the configuration management subsystem ensures is loaded properly into the maintenance information system database is | select serially controlled and time change items
🗑
|
||||
The IMDS is the production-oriented, automated maintenance management system at the | unit level
🗑
|
||||
The IMDS subsystem that provides information about jobs performed by maintenance activities is the | Job Data Documentation
🗑
|
||||
The GAS is normally sent out | 90 days after graduation
🗑
|
||||
A list of training courses available for an AFSC can be found in the | CFETP, Park II
🗑
|
||||
Tasks that a person is expected to perform in a duty position or WC but are not included in the CFETP, Part II, or AFJQS are listed | on an AF Form 797, Job Qualification Standard Continuation/Command JQS
🗑
|
||||
The first step taken when reviewing an Air Force Technical Order (AFTO) 244 is to | match the ID number on the form with the ID number on the unit
🗑
|
||||
The two maintenance stands on which C-1 maintenance stand can be installed as an extension are the | B-1 and B-2
🗑
|
||||
The maintenance stand that has an adjustable height of 13'-20' is the | B-2
🗑
|
||||
The maintenance stand that is a scissor-type is the | B-4
🗑
|
||||
The lifting of an aircraft jack is called a | ram
🗑
|
||||
The low- and high-pressure capabilities, in psig, of the NSU-L75 nitrogen servicing unit are | 05-350; 350-3600
🗑
|
||||
The usable pressure range, measured in psi, of the MC-1A air compressor is | 0-3200 psi
🗑
|
||||
The MC-2A air compressor is capable of delivering air at a maximum pressure, measured in psi, of | 200
🗑
|
||||
The maximum BTUs per hour output of the H-1 heater is | 400,000
🗑
|
||||
The new generation heater oil burner and combustion blower are powered by | 60- Hz alternator
🗑
|
||||
The temperature range the C-10 air conditioner is capable of delivering conditioned air at is | 47*F to 200*F
🗑
|
||||
The FL-1D floodlight consists of two | 1000 watt lamp fixtures
🗑
|
||||
The unit capable of providing AC and DC electrical power, in addition to pneumatic power, for ground maintenance is the | A/M32A-60
🗑
|
||||
The MK-3A-1 is driven by a | electric motor
🗑
|
||||
The MB-4 tractor incorporates | four-wheel steering, four-wheel drive
🗑
|
||||
Aluminum alloy washers are used with steel bolts on aluminum alloy parts in low-torque applications to | prevent corrosion
🗑
|
||||
Special bolts are identified by | the bolt head marked with the letter S
🗑
|
||||
The bolt used where heavy tension or lengthwise stress must be sustained is a | hexhead
🗑
|
||||
The number of thread that must be showing through a self-locking nut for maximum locking effect is at least | two
🗑
|
||||
Aircraft cable size is determined by its | diameter
🗑
|
||||
A 7 X 19 cable has | 7 strands with 19 wires per stand
🗑
|
||||
The correct way to detect broken wires on a cable is to | pass a cloth along the length of cable
🗑
|
||||
A push-pull rod end engagement is checked | by inserting safety wire in the hole in the end of the terminal
🗑
|
||||
A hose may bear a colored indicator stripe to show | its direction of natural lay
🗑
|
||||
When using 0.032-gage safety wire, there should be how many turns per inch? | 7-12
🗑
|
||||
When securing widely spaced bolts by the double-twist safetying method, the maximum number of bolts that may be wired in a series is | three
🗑
|
||||
When is it permissible to reuse cotter pins? | Never
🗑
|
||||
On a standard electrical connector, the key and keyway are located | adjacent to the A or 1 pin
🗑
|
||||
To tighten cannon plugs, do not use | channel lock pliers
🗑
|
||||
The number of positions on the function switch of the AN/PSM-37 multimeter is | seven
🗑
|
||||
To measure current flow, you connect an AN/PSM-37 multimeter in | a series in the circuit
🗑
|
||||
When the H symbol is shown on the Fluke multimeter display, the | manual range mode is indicated
🗑
|
||||
When measuring resistance on a Fluke multimeter, the letters OL indicate | overload
🗑
|
||||
Prior to using a torque wrench, cycle the torque wrench through the breakaway torque at the | maximum setting at least six times
🗑
|
||||
The responsibility for ensuring good supply discipline is practiced resides with | supervisors at all levels
🗑
|
||||
Shop stock should not normally exceed | 90-days usage or the U/I or unit pack, whichever is greater
🗑
|
||||
The expandability, recoverability, reparability code that designates a repair cycle asset is | XF
🗑
|
||||
Consumable items are identified by the expandability, recoverability, reparability code (ERRC) | XB3
🗑
|
||||
The DD Forms easily identified by their green margins and letters are the | 1577-2, Unservicable (Reparable) Tag-Material, and 1577-3, Unservicable (Reparable) Label-Material
🗑
|
||||
The deficiency report (DR) category that results in a work line stoppage is | 1
🗑
|
||||
Engines overhauled by depot are covered against defects in workmanship for | 100 hours of operation or one year from the date of receipt
🗑
|
||||
The Air Force Technical Order Form 781 must be removed from the forms binder | after the event number is entered at the maintenance debreifing
🗑
|
||||
The Air Force Technical Order Form 781K is used to document | engine data
🗑
|
||||
Responsibility for maintaining the Air Force Technical Order 781-series forms binder rests with the | crew chief
🗑
|
||||
The action necessary to clear an erroneous red X symbol is | an authorized individual signs the INSPECTED BY block and initials over the symbol
🗑
|
||||
The symbol entered on the forms if an aircraft exceeds the PDM cycle by 90 days and an extension is not granted is a | red X
🗑
|
||||
The inspection usually performed just prior to takeoff and that may include operational checks of some systems is the | end-of-runway
🗑
|
||||
The BPO is performed to | determine if the aircraft is suitable for another flight
🗑
|
||||
If an aircraft is idle for more than 30 or 90 days, the inspection required is | calendar
🗑
|
||||
The type of inspection that ensures the completeness of historical documents is | acceptance
🗑
|
||||
The AF IMT 2691 is used to | account for aircraft-21 TO equipment
🗑
|
||||
Corrosion or deterioration of a metal part continues until the part is | exhausted or salvaged
🗑
|
||||
Galvanic corrosion occurs when | different metals are in contact with each other and an electrolyte
🗑
|
||||
The frequency of cleaning an aircraft exterior depends, for the most part, on | environmental conditions
🗑
|
||||
The type of cleaners not very effective on grease, but excellent for interior lightly soiled areas, plastics, and instrument glass covers is | detergent
🗑
|
||||
The solution used to treat areas affected with electrolyte from a lead-acid battery is | sodium bicarbonate
🗑
|
Review the information in the table. When you are ready to quiz yourself you can hide individual columns or the entire table. Then you can click on the empty cells to reveal the answer. Try to recall what will be displayed before clicking the empty cell.
To hide a column, click on the column name.
To hide the entire table, click on the "Hide All" button.
You may also shuffle the rows of the table by clicking on the "Shuffle" button.
Or sort by any of the columns using the down arrow next to any column heading.
If you know all the data on any row, you can temporarily remove it by tapping the trash can to the right of the row.
To hide a column, click on the column name.
To hide the entire table, click on the "Hide All" button.
You may also shuffle the rows of the table by clicking on the "Shuffle" button.
Or sort by any of the columns using the down arrow next to any column heading.
If you know all the data on any row, you can temporarily remove it by tapping the trash can to the right of the row.
Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.
Normal Size Small Size show me how
Normal Size Small Size show me how
Created by:
kjcarter
Popular Physics sets