Busy. Please wait.

Don't have an account? Sign up

taken

Age:

12 or younger
13 or older

Make sure to remember your password. If you forget it there is no way for StudyStack to send you a reset link. You would need to create a new account. Your email address is only used to allow you to reset your password. See our Privacy Policy and Terms of Service.

Already a StudyStack user? Log In

Reset Password

Enter the email address associated with your account, and we'll email you a link to reset your password.

Upgrade to remove ads

MK-16 Mod 0/1

Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.

Normal Size Small Size show me how

Created by: NEDUFCPOA

Question	Answer
What is the MK-16 Mod 0 Max depth?	The Max Depth for MK-16 Mod 0 is 200 FSW when using HeO2 (84/16), and 150 FSW when using Air (N2O2).
Is the use of a T-Bit authorized for normal diving operations?	No. The use of a FFM is required during normal MK-16 diving operations.
What factors affect CO2 absorbent duration?	Operating temperature and depth directly affect CO2 absorbent performance.
What is the PPO2 Set Point for Mod 0?	The Mod 0 Set point is .75.
How often should a MK-16 diver perform a MK-16 dive to maintain his qualification?	A MK-16 Diver is required to make a MK-16 dive once every six months to maintain his qualification.
How much pressure is required to drive the reducer?	A reserve pressure of 500 PSI is required to drive the reducer.
Min and Max Canister duration?	Maximum Canister duration is 300 minutes. Minimum canister duration is 100 minutes. Chart can be found in Dive Man Rev 6 17-11.
What are the general Diving equipment requirements for MK-16 diving operations?	General Requirements for MK-16 Diving: 1. Motorized Safety Boat. 2. Two-Way Radios 3. Flash light 4. Dive Flags 5. >2 quarts fresh water in case of chemical injury.
What are the Equipment requirements for a MK-16 Dive Supervisor?	Minimum equipment for MK-16 Dive Supervisor are: 1. Dive Watch 2. Dive Bill 3. Air 'D' Tables 4. MK-16 Dive Tables 5. Recall device
When is a Recompression chamber required on the dive station for MK-16 Diving Operations?	A recompression chamber is only required when exceeding the max working limit.
What is the maximum descent rate for MK-16?	60 FPM is the Max Descent Rate for MK-16 diving.
Is Surface decompression authorized for MK-16 Diving Operations?	Surface decompression is not authorized for MK-16 Diving Operations.
How often is LO-MU Certification performed?	LO-MU certification is performed a minimum of every five years.
What documentation is required in a MK-16 Rig Jacket?	At a minimum, a Rig Jacket should include the following: 1. A Pedigree Report (detailing serialized components) 2. Certification Letter 3. Maintenance Log 4. Most Recent Initial and predive.
When is an Initial Setup Required?	An Initial Setup is required after any repair, any sensor is replaced or repositioned, and/or every six months.
What is the PPO2 Setpoint for MK 16 Mod 1?	.75 and 1.3
When does the MK-16 Mod 1 Transition?	The Mod 1 transitions from .75 to 1.3 ata at approximately 33 FSW on descent. On ascent, the transition occurs at approximately 13 FSW.
When deploying the EBS for MK-16 Mod 1 Diving Operations, what depth is the EBS initially lowered to?	The EBS is lowered to 40 FSW to allow the rig to transition from .75 to 1.3 ata.
Name three ways to reduce Pulmonary or CNS Oxygen Toxicity during multi day diving.	1. Limit dive time to 4-hours per day. 2. Limit dive time to 16 hours per week 3. Conduct shallower dive in .75 ata mode (when using Mod 1)