Question | Answer |
What should you do if you are unsure about how to use a tool? | ASK YOUR TEACHER |
What should you ALWAYS pay attention to... | Hand placement and surroundings |
You should never leave a tool... | unattended or uncovered |
When should safety glasses be worn? | when any tool/equipment is in use |
When around tools/equipment, your hair should be_________ because_________. | Tied back because it can easily get caught or block your peripheral version. |
Johnny Blaze caught on fire because he was wearing | Loose clothing |
You are not allowed to use the tools or equipment if you are not wearing | Closed toed shoes. |
If you are very upset or angry you should not | use the tools/equipment |
Do not use tools or equipment if | a teacher is not present
if you did not ask first
if the tool or equipment is broken
if you are upset or angry |
You must clean up any __________ by organizing them in the designated boxes. | scrap materials or waste that is created |
When should you report an accident? | Immediately |
In the case of a medical emergency, you should do this first | Inform the teacher immediately. |
In the case of a medical emergency, should the students go to the nurse? | No, the nurse should come to the room. |
Hand tools should be carried like this. | below your waist with a firm grip. |
If you are using a box cutter or exacto knife, the cover should remain on the blade when | the tool is not in use |
What can you do to an exacto knife to keep it from rolling off the table? | Flag it |
True or False: A sharp tool is a safe tool | True: A sharp tool is safer to use because it cuts the material with ease. If you have to force the blade into the material, an accident is more likely to occur. |
If you are cutting a piece of material with a exacto knife or box cutter, you should always use a | cutting mat |
You are require to do this before you use a tool/piece of equipment and after you are done with it | SIGN IN/SIGN OUT |
What do you do if a blade falls out of an exacto knife | Do not leave the blade unattended and ask a teacher to assist you in replacing the blade. |
Always assume the hot-wire cutter is _________ when you approach it. | HOT - Turned on |
The hot wire cutter heats up | Immediately |
If the hot wire cutter is turned on, this should also be turned on to eliminate fumes | air fiter |
When cutting any material, the material should be placed... | Flat on the surface - use a straight edge/fence to assist with the cut |
If you push too hard on the wire (hot wire cutter), what could happen? | The wire could break |
When using a hand-drill to cut any material, first secure the material with _______ | c- clamps |
Never use your ___________to secure a material | hands |
What part of the drill bit cuts the material? | the tip of the drill bit |
How do you replace a drill bit? | Loosen and tighten the chuck |
When you are done using the drill, place the battery in the | charger |
The saw can cut thin materials, including | foam, plastic, cardboard, foam core, dowel rod, and plywood or softwood |
Only apply pressure when the saw blade is on the | downstroke |
If the machine sounds, smells, or looks funny or breaks when you are using it, you should... | turn the machine off and tell the teacher. |
When you are done using the classroom equipment, you should always do these two things | Turn it off
Tell the teacher |
Do not leave the Glowforge unit __________while operating - always stay within __________. | unattended
sight |
Do not put things ________ ____________ ______ the Glowforge. | On top of |
In order to use a material in the glowforge, it MUST be | laser compatible |
DO NOT REMOVE THE.... | EXHAUST HOSE |
DO NOT _________ materials inside the Glowforge | stack |
Do not stare directly at... | The laser ( Glowforge head unit) |
When the exhaust turns off, that means that | the fumes have been outputted
you can remove your material |
DO NOT attempt to ______ or _________ the Glowforge unit in any way. | alter or modify |
What gases are in the laser tube? | Hydrogen, Helium, and carbon dioxide |
To cancel a print on the Glowforge you can... | Cancel it on the computer display or
open the lid ever so slightly |
With the crumb tray installed, what is the maximum material thickness that can be used? | 1/2" |
The laser head moves on which two axes? | x and y |
What file types does the Glowforge render? | JPEG, PDF, PNG, SVG |
What is the difference between a raster and a vector image? | Raster -pixel based
Vector - made of lines/shapes |
Which color represent the cut operation? | RED |
Which color represent the score operation? | GREEN |
which color represent the engrave operation? | BLUE |
In which order should the operations be preformed? | ***Engrave, score and then cut. |
If you choose to trace an image, the Glowforge will ask you to select the area that your want to
A. Keep
B. Cut away. | B. Cut away |
When using the computers, students are prohibited from searching | inappropriate content or images. |
Students are prohibited from tampering with | computer cords |
Once clean up has been called, all work must | STOP immediately . |
What should you use the clean surfaces? | Dust plans or shop-vac. |
If the room is not clean when the bell rings then | NO ONE LEAVES |
At the end of the day, what matters most? | Safety. |
Loose stringy things don't mix well with .... | fast spinny things |
Never plug the strip heater into .... | an extension cord |
Before you apply a work piece to the strip heater you must... | wait for it to reach about max temperature ( 3-5 minutes) |
True or False: The strip heater must be attended when it is warming up, in use, and cooling down. | True |
True or False:You, the student, are responsible for changing the dremel attachment | False - Ask Ms. Coker |
What speed should the dremel be set to when you turn it on? | Speed 5 |
Describe your stance and hand placement when using the dremel. | Always keep your hands and fingers well clear of the bit.
Do not overreach - keep proper footing and balance at all times. |
True or False: Loose clothing/accessories are okay to wear when operating the drill press as long as you are careful | False |
What does the chuck key do? | Lock the drill bit inside the chuck |
What does the chuck do? | Hold the drill bit |
When using the drill press, how do you secure your work piece? | Clamps |
Why should you center punch your work piece using the drill bit? | Make sure drill bit is lined up with desired location
Help feed the bit into the material |
Where is the on/off button located on the drill press? | On the head of the machine - in your direct line of vision on the front. |
True or False: The chuck key should stay in the chuck during operation | False - put it back in the holder on the side of the machine |
When you're done with the drill press what do you do with the drill bit? | Use the chuck key to remove the bit from the chuck. Put the drill bit back into the storage case. |
True or False: When using the drill press, should put your work piece directly on the table so it lays flat. | False - you should but a scrap piece under your workpiece |
On the drill press, how do you change the depth of the cut? | Adjust the table high or the depth gauge ( or both) |
True or False: Students are prohibited from tampering with computer cords and cables. | True |
What do you do when CLEAN UP is called | Stop what you are doing, turn off equipment, disassemble and store properly. The throw out unusable scraps and use dust pans to clean surfaces. Use the shot vac to clean us saw dust on the floor. |
If you are done cleaning your area you are required to.... | Help your classmate clean up the rest of the room |
What type of tool is a dremel? | A rotary tool - used for grinding, sanding, polishing, or machining material (typically metal, but also plastic or wood). |
What two dremel attachments are used with the routing table? | Drum sander and profile bits ( sculpts edge of material) |
When using the routing table ( dremel), which direction do you feed the material? | Right to left |
When using the bandsaw, you should hold the material against the blade as you turn on the saw. T or F? | FALSE - wait until the machine is running at full speed |
Remove scraps from the Band Saw while the blade is still moving. T or F? | FALSE - turn off the machine and wait until the blade comes to a complete stop |
On the bandsaw the blade guard should be how far from the top of your material? | 1/8 - 1/4th inch |
The vinyl cutter cuts the vinyl using a ... | Small Blade |
As a covid guideline, you must use the wipes to wipe down | Your workstations, tools, and safety glasses |