Refer to the exhibit. A network administrator is verifying the configuration of inter-VLAN routing. Users complain that PC2 cannot communicate with PC1. Based on the output, what is the possible cause of the problem?

The encapsulation dot1Q 5 command contains the wrong VLAN.

Refer to the exhibit. After attempting to enter the configuration that is shown in router RTA, an administrator receives an error and users on VLAN 20 report that they are unable to reach users on VLAN 30. What is causing the problem?

RTA is using the same subnet for VLAN 20 and VLAN 30.

A router-on-a-stick config was implemented for VLANs 15, 30, & 45, according to the show running-config command output. PC -VLAN 45-172.16.45.0 /24 network are having trbl connecting VLAN 30 -172.16.30.0 /24 network. Which is problem?

There is an incorrect IP address configured on GigabitEthernet 0/0.30.

Refer to the exhibit. The switch does the routing for the hosts that connect to VLAN 5. If the PC accesses a web server from the Internet, at what point will a VLAN number be added to the frame?

No VLAN number is added to the frame in this design.

While configuring inter-VLAN routing on a multilayer switch, a network administrator issues the no switchport command on an interface that is connected to another switch. What is the purpose of this command?

To create a routed port for a single network.

Refer to the exhibit. PC1 is unable to communicate with server 1. The network administrator issues the show interfaces trunk command to begin troubleshooting. What conclusion can be made based on the output of this command?

Interface G0/2 is not configured as a trunk.

Help

Options

Question

Refer to the exhibit. Communication between the VLANs is not occurring. What could be the issue?

click to flip

focusNode

Didn't know it?
click below

Knew it?
click below

Don't know

Question

Refer to the exhibit. A network administrator is configuring inter-VLAN routing. However, the communication between VLAN 10 and VLAN 20 fails. Based on the output of the show vlan command, what is the cause of the problem?

Remaining cards (9)

Know

retry

shuffle

restart

0:00

Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.

Normal Size Small Size show me how

intervlan

Question	Answer
Refer to the exhibit. Communication between the VLANs is not occurring. What could be the issue?	The Gi1/1 switch port is not in trunking mode.
Refer to the exhibit. A network administrator is configuring inter-VLAN routing. However, the communication between VLAN 10 and VLAN 20 fails. Based on the output of the show vlan command, what is the cause of the problem?	Gi1/1 and Gi1/2 are not assigned to their respective VLANs.
Refer to the exhibit. A network administrator is verifying the configuration of inter-VLAN routing. Users complain that PC2 cannot communicate with PC1. Based on the output, what is the possible cause of the problem?	The encapsulation dot1Q 5 command contains the wrong VLAN.
Refer to the exhibit. After attempting to enter the configuration that is shown in router RTA, an administrator receives an error and users on VLAN 20 report that they are unable to reach users on VLAN 30. What is causing the problem?	RTA is using the same subnet for VLAN 20 and VLAN 30.
A router-on-a-stick config was implemented for VLANs 15, 30, & 45, according to the show running-config command output. PC -VLAN 45-172.16.45.0 /24 network are having trbl connecting VLAN 30 -172.16.30.0 /24 network. Which is problem?	There is an incorrect IP address configured on GigabitEthernet 0/0.30.
Refer to the exhibit. The switch does the routing for the hosts that connect to VLAN 5. If the PC accesses a web server from the Internet, at what point will a VLAN number be added to the frame?	No VLAN number is added to the frame in this design.
While configuring inter-VLAN routing on a multilayer switch, a network administrator issues the no switchport command on an interface that is connected to another switch. What is the purpose of this command?	To create a routed port for a single network.
What is a characteristic of a routed port on a layer 3 switch?	It is not assigned to a VLAN.
On a Cisco switch, where is extended range VLAN information stored?	Running configuration file
Refer to the exhibit. PC1 is unable to communicate with server 1. The network administrator issues the show interfaces trunk command to begin troubleshooting. What conclusion can be made based on the output of this command?	Interface G0/2 is not configured as a trunk.

Created by: ninjanicki

"Know" box contains:
Time elapsed:
Retries: