Help
Options
Didn't know it?
click below
click below
Knew it?
click below
click below
Don't Know
Remaining cards (0)
Know
retry
shuffle
restart
0:00
Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.
Normal Size Small Size show me how
Normal Size Small Size show me how
15-men haircutting +
15-men haircutting + hairstyling (shapes, lines, angles, tools, texture
| Term | Definition |
|---|---|
| A round face benefits from ___. | extra height on top |
| A square face looks good with ___. | wavy bangs that blend into temples |
| Concave profiles require ___. | a close hair arrangement over the forehead |
| A straight profile tends to be the most balanced and | can usually wear any hairstyle successfully |
| Prominent nose shapes include hooked, ___, and large noses. | pionted |
| Reference points are points on the head that mark areas where the surface of the head changes or the behavior of the hair changes | as a result of the surface changes |
| The ___ is also known as the crest, temporal, horseshoe, or hatband area of the head. | parietal ridge |
| Vertical lines facilitate ___ while cutting | the projection of the hair at higher elevations |
| Diagonal lines may be used to create a ___ effect at the perimeter or to blend longer layers to shorter layers within a haircut. | stacked layered |
| Use of a vertical parting projected at 45 degrees, with the fingers holding the partings angled at a ___, will create a tapered effect. | 45-degree diagonal |
| A 90-degree elevation is used to create ___. | uniform layers |
| The cutting line refers to the ___. | position of the fingers when cutting a section of hair |
| ___ are classified as being either stationary or traveling | Guides |
| A weight line refers to the ___. | heaviest perimeter area of a 0-elevation or 45-degree cut |
| Use maximum tension on ___. | straight hair to create precise lines. ī |
| Cutting above the fingers is frequently used in men's haircutting to cut and blend layers in the ___ area. | All answers are correct. (top, crown, and horseshoe) |
| Cutting below the fingers is most often used to create design lines at the ___. | perimeter of the haircut |
| When using the ___ technique, both the fingers and the comb should be in a horizontal position parallel to the floor. | fingers-and-shear |
| The ___ cutting technique is normally performed in the nape. | comb-over-shear |
| When using the shear-over-comb technique, place the third finger ___. | on the finger brace |
| In the shear-over-comb technique, the comb is held in the left hand with the fingers on top of the teeth and the thumb ___. | on the backbone of the comb |
| In the shear-over-comb technique, align the still blade of the shears with the comb ___. | below the still blade |
| The arching technique can be used to thin ___. | whorls |
| When using the arching technique, the barber ___. | uses the center of the shear blade |
| The standard techniques for clipper cutting are ___ cutting and clipper-over-comb cutting. | clipper and razor |
| When tight, curly hair is cut ___, the clipper blade gets clogged and patches and spots may be left. | with a short blade |
| Many barbers prefer to use an outliner or trimmer with a fine cutting edge to ___. | form the cutting line |
| Very short curly hair requires true ___ clipper cutting technique. | shorthand |
| Size 0000 detachable blades are ___. | closest to shaving |
| When using the clipper-over-comb cutting technique, the ___ is placed on the top left side of the clipper. | thumb |
| Begin in the nape area ___. | only when using an adjustable blade clipper |
| Short styles, such as ___, have a high taper and are blended in the crest areas, | All answer are correct. (butch, crew cuts, and fades) |
| Flat tops are traditionally slightly longer in the ___ sections and flat across the top of the head form | front and crest |
| A brush cut is also called a ___. | crew cut |
| The Quo Vadis is a popular very short haircut style that is suitable for ___ hair. | very curly |
| Long haircut styles usually require the least amount of ___. | clipper tapering |
| When performing a ___ cut, clipper cutting in the nape should be performed with the clipper tilted on its heel until reaching a point about midway to the ears. | medium length |
| In a ___ style, when cutting around the ears, remove about 1 inch from the hairline, then use an outliner to trim the sideburns and around the ear areas. | semi-short |
| For a ___ style, clipper cutting is performed up to the occipital areas and on the sides to the bottom of the crest. | medium-length |
| Razor cutting is not suitable for cutting--- layers cuts or one length cut | layers cuts |
| The razor-over-comb technique is often used to taper nape areas or to ___. | soften weight lines |
| In the two-section method for razor haircutting, the hair is parted ___. | from the ear across the crown |
| Replace dull razors ___. | during a cut if necessary |
| Thinning, slicing, and carving ___. | remove bulk |
| When shaving the ___ areas, hold the razor for a reverse backhand stroke | left side outline |
| A vertical subsection cut at a ___ projection can be cross-checked by parting off the subsections horizontally at 90 degrees. | 90-degree |
| When shaving an outline on ___ hair, first shave the front hairline. | tightly curled |
| Clippers are used to facilitate ___ on a fade cut. | blending |
| To create a crew cut, using #1 1/2 blade, cut with the grain, and angle the comb from the ___. | crown to the front |
| Use a changeable-blade straight razor to perform a ___. | head shave |
| When ___, remove excess hair using a balding clipper blade if available. | shaving the head |
| Shear-over-comb is the most popular technique for eyebrow trimming but a(n) ___ technique can be used as well. | outliner-over-comb or small blade guard |
| Finger-styling produces a ___ look than brush styling. | more textured |
| When ___ and the dryer are used to create wave patterns and direction in the hair, the technique is called blow waving. | a comb or brush |
| One of the most popular types of ___ is on-the-scalp cornrows. | braids |
| To form a braid, place fingers close to the base and first cross the ___. | left strand under the center strand |
| The comb is effective __ hair locking. | during the early stages of |
| In cutting a flat top the hair is shortest in the _________ (on the top of the head) | Apex |
Created by:
cylearc1