CH 337: Unit 2 Word Scramble
|
Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.
Normal Size Small Size show me how
Normal Size Small Size show me how
| Question | Answer |
| What characterizes a pure organic compound? | no detectable impurities |
| For what type of compounds is recrystallization the major mode of purification? | Solids |
| In its simplest form what does the process of recrystallization involved? | recrystallization involves the preparation of a hot saturated solution which is then allowed to cool |
| What occurs as a hot saturated solution gradually cools? | The solute precipitates |
| In order to obtain a purer sample what must be true about the impurities? | the impurities dissolve in the hot solvent and remain in solution even as the hot saturated solution is cooled. |
| How does the rate of cooling affect crystal growth? | Slow cooling promotes slow crystal growth which promotes the formation of larger, pure crystals. Rapid cooling promotes rapid crystal growth promotes the formation of smaller, less pure crystals. |
| What useful adage can guide one during the trial-and-error process of solvent selection? | The adage "like-dissolves-like" |
| As the number of functional groups present increases, solubility increases | statement |
| What two high-polarity solvents are commonly used for recrystallization? | Methanol and ethanol (water is too polar) |
| What two low-polarity solvents are commonly used for recrystallization? | diethyl ether and ethyl acetate |
| Why should one use a steam bath or hot-water bath, rather than a hot plate or open flame, to heat solvents such as ether, hexane and petroleum ether? | These solvents are very flammable |
| What is the most crucial aspect of recrystallization? | solvent selection |
| What characterizes an effective recrystallization solvent? | Has to be all 3: Be chemically inert, have a very high capacity at the boiling point of the solvent and have a low capacity at the solvent's freezing point and dissolve impurities |
| What rule of thumb should be followed in order to select an Erlenmeyer flask of appropriate size? | The flask should be 2 to 3 times larger than the volume of solvent one expects to use |
| In the absence of specific solubility data what rule of thumb should be followed in order to select an appropriate quantity of solvent? | Solvent volume should be 20 to 40 times the mass of the sample to be recrystallized |
| What characterizes the manner of solvent addition? | added incrementally |
| How are insoluble impurities removed from the hot, saturated solution? | hot gravity filtration |
| Under what circumstances are seed crystals used? | when the solute doesn't crystalize from the cooling saturated solution |
| Aside from mechanical losses during recrystallization what other factors might lead to low recovery of material? | a) too much solvent used b) crystallization during hot, gravity filtration c) vacuum filtration preformed prior to complete crystallization |
| For how long should one dry a produce that has been recrystallized from a high boiling-point solvent? | At least over night (a week in our class) |
| What is the 1st step to judge if a solvent will be suitable to use as a recrystallization solvent? | Combine a small quantity of the test solvent (5-10 drops) and a small quantity of sample (20-30 mg) in a test tube at room temp. Mix by shaking. If the sample dissolves then the solvent is not good. If the sample doesn't dissolve go to step 2. |
| What is the 2st step to judge if a solvent will be suitable to use as a recrystallization solvent? | Heat the contents of the test tube to the boiling point of the solvent. If the sample doesn't dissolve the solvent will not be a good solvent. If the sample dissolves go to step 3. |
| What is the 3st step to judge if a solvent will be suitable to use as a recrystallization solvent? | Allow the contents of the test tube to cool. If crystals don't form within 10-20 minutes the solvent isn't a good choice. If crystals do form it is likely to be an effective recrystallization solvent. |
| What are the 3 basic steps in recrystallization? | 1) preparation of a hot, saturated solution at the solvent's boiling point followed by removal of any insoluble impurities 2) gradual cooling of the hot, saturated solution 3) collection of crystalline material by vacuum filtration |
| Identify two methods for transferring a solid to the recrystallization flask? | a) the use of creased weighing paper b) the use of creased weighing paper and powder funnel |
| Why is it advisable to set aside a small amount of the crude material before preforming a recrystallization? | For use as seed crystals and to use to get melting point |
| After the flask has cooled to room temp is there any advantage to cooling it in an ice-water bath? | Yes. The advantage to cooling in an ice-water bath is that it facilities maximum crystallization |
| What actions could one take in the event that no material crystalizes after 15 minutes of cooling in an ice-water bath? | Add seed crystals |
| What is the standard system for collecting products purified by recrystallization? | Vacuum filtration |
| Why is it advisable to employ a trap flask during vacuum filtration? | To prevent the flow of water from the water aspirator to the filter flask |
| Why should one pull some of the recrystallizing solvent through the filter paper, by application of the vacuum source, prior to filtration? | To seat the filter paper |
| What quantity of water should be used to recrystallize a 1.2g quantity of salicylic acid (solubility of salicylic acid in water: 1g/460mL at 25C, 1g/15mL at 100C) | Volume of water at 100C required to dissolve. 1.2g x 15 mL/g = 18mL |
| How much salicylic acid will crystalize when the solution prepared above is allowed to cool to 25C? | nass remaining in solution after cooling to 25C = 18mL x 1g/460mL = .04g Mass of salicylic acid that crystalized after cooling = 1.2 - .04 = 1.16g |
| What is the maximum percent recovery of salicylic acid in this scenario? | 1.16/1.20 x 100% = 96.7% |
| How to increase the percent recovered? | ice-bath (lowers temp) |
| Assuming 38.2 mL of water was used in the preceding questions, what is the maximum percent recovery of salicylic acid that the solution was cooled to 25C? | 38.2 mL (1g/460mL) = .083g 1.20-.083 = 1.12 1.12/1.2 x 100% = 93.3% |
Created by:
leelow13