Aircraft Structural Maintenance Journeyman
Quiz yourself by thinking what should be in
each of the black spaces below before clicking
on it to display the answer.
Help!
|
|
||||
|---|---|---|---|---|---|
| What type of aluminum allot tubing do you use to repair a hydraulic system that carries high pressures up to 3,000 psi? | show 🗑
|
||||
| show | Corrosion resistant stainless steel tubing type 304.
🗑
|
||||
| show | Blue.
🗑
|
||||
| To be considered objectionable, the depth for a dent on a tubing assembly is what? | show 🗑
|
||||
| The probable cause of excessive burrs while cutting tubing with tube cutter is what? | show 🗑
|
||||
| show | Flush with a TO approved solvent.
🗑
|
||||
| To properly locate the start point on a piece of tubing that will have only one bend, you do what? | show 🗑
|
||||
| show | Place a piece of emery cloth between the tubing and the clamp block.
🗑
|
||||
| show | Sand.
🗑
|
||||
| To correctly construct a single flare, you make the outside diameter what? | show 🗑
|
||||
| For tubing flares to seat properly, they must be what? | show 🗑
|
||||
| To properly use the squaring- and burring- head assembly on the power-flaring machine to work a piece of tubing, you position the tubing in a vise so it is what? | show 🗑
|
||||
| While using the squaring-and burring-head assembly on the power flaring machine the probable cause of more inside chamfer on one side of a piece of tubing and more outside chamfer on the opposite side is what? | show 🗑
|
||||
| show | Change the flaring center setting to match the OD of the new size tubing.
🗑
|
||||
| To remove the tubing after you have finished making a flare with the double-flaring machine, you move the operating lever where? | show 🗑
|
||||
| show | Jaw nut.
🗑
|
||||
| show | Never.
🗑
|
||||
| show | Corresponds with the silver side of the yoke.
🗑
|
||||
| show | Yellow.
🗑
|
||||
| To properly make a dynatube repair, you should have what degree of chamfer on the inside diameter of a tube? | show 🗑
|
||||
| To inspect the ring position of a swage Pemalite fitting, you use what? | show 🗑
|
||||
| show | Ensure the alignment mark is still visable.
🗑
|
||||
| How do you position a rynglok fitting on the tube before swaging? | show 🗑
|
||||
| show | Outside diameter.
🗑
|
||||
| show | 8,000-8,500 pounds per square inch gage.
🗑
|
||||
| When installing you military specification fittings which type of aluminum alloy tubing would you use as a replacement for 5052-0 aluminum alloy tubing? | show 🗑
|
||||
| show | Tighten the drive screw an additional 1/8 - 1/4 a turn.
🗑
|
||||
| show | 1/2 the wall thickness.
🗑
|
Review the information in the table. When you are ready to quiz yourself you can hide individual columns or the entire table. Then you can click on the empty cells to reveal the answer. Try to recall what will be displayed before clicking the empty cell.
To hide a column, click on the column name.
To hide the entire table, click on the "Hide All" button.
You may also shuffle the rows of the table by clicking on the "Shuffle" button.
Or sort by any of the columns using the down arrow next to any column heading.
If you know all the data on any row, you can temporarily remove it by tapping the trash can to the right of the row.
To hide a column, click on the column name.
To hide the entire table, click on the "Hide All" button.
You may also shuffle the rows of the table by clicking on the "Shuffle" button.
Or sort by any of the columns using the down arrow next to any column heading.
If you know all the data on any row, you can temporarily remove it by tapping the trash can to the right of the row.
Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.
Normal Size Small Size show me how
Normal Size Small Size show me how
Created by:
Justin84