SE
Quiz yourself by thinking what should be in
each of the black spaces below before clicking
on it to display the answer.
Help!
|
|
||||
|---|---|---|---|---|---|
| When using a table saw, feeding stock, what must be used? | A push stick
🗑
|
||||
| Lumber stored in tiers will be: | Stacked, blocked and interlocked
🗑
|
||||
| Qualified operators who have been TRAINED and issued a qualified operators card will be permitted to use which tools? | Powder-actuated tools
🗑
|
||||
| Chicken ladders or crawling boards will have the cleats spaced at intervals not to exceed how many inches? | 24 inches
🗑
|
||||
| Who will be consulted for evaluation of the need for respiratory protection, during masonry operations? | Installation BE
🗑
|
||||
| Scaffolds with wheels constructed on the base section will not be used unless _____ are intact and at least ______ on each side is locked to prevent movement. | All wheels; 1 wheel
🗑
|
||||
| Never be any closer than how many feet to electrical power lines? | 10 feet
🗑
|
||||
| Tests and certification of cranes and hoists will be by ___. | Experienced, qualified inspectors
🗑
|
||||
| Certification, inspection, and test reports will be available on the premises where the crane or hoise is located or ___. | In the supervisors office.
🗑
|
||||
| Only personnel designated as qualified by the ____ shall be permitted to operate cranes. | Supervisor
🗑
|
||||
| What will be stenciled or otherwise plainly marked on all jacks and hoists? | Load ratings
🗑
|
||||
| Flammable wastes wuch as oily rags, steel wool, sweepings, and excelsior will be contained in what type of containers? | Self closing metal containers.
🗑
|
||||
| Two-wheeled hand trucks will be parked in what type of position? | Upright
🗑
|
||||
| Pallet loads will be stacked with how much clearance on all sides to prevent dislocation of adjacent stacks? | 2 inches
🗑
|
||||
| Corner markings must be not less than ___ high and ___ wide and colored with alternating yellow/black diagonal stripes ___ wide. | 30"high and 24”wide; 3-5” wide.
🗑
|
||||
| What type of lighting will not be used in flammable storage areas? | Fluorescent lighting
🗑
|
||||
| How much clearance will be maintained between stacks and sprinklers when stacks are less than 15’ high? | 18 inches
🗑
|
||||
| Stacks will not be located within how many inches of light and/or heat fixtures? | 18 inches
🗑
|
||||
| Flammable liquids are defined as: | A liquid with a closed cup flash point below 100F
🗑
|
||||
| Combustible liquids are defined as: | A liquid with a closed up flash point above 100F
🗑
|
||||
| Facilities located within how many feet of another building must have a blank wall? | 50 feet
🗑
|
||||
| Facilities with a blank wall must also possess a fire rating of how many hours? | 2 hours
🗑
|
||||
| What type of lighting will be used on all electrical equipment and wiring in storage rooms/buildings? | Spark proof, explosion proof, electrical fixtures
🗑
|
||||
| How many personnel will work together when energized high voltage circuits are exposed? | 2
🗑
|
||||
| Personnel whose normal daily job exposes them to energized circuits will receive what training? | CPR, shock management, care of persons with open wounds or burns
🗑
|
||||
| CPR training must be accomplished with in how many days of assignment? | 30 days
🗑
|
||||
| High Voltage is how many volts or greater? | 600 volts
🗑
|
||||
| Vehicle or mechanical equipment with elevated structures will not operate within how many feet of overhead power lines? | 10ft
🗑
|
||||
| The 3 primary phases of a POL operation are: | Fuel storage, fuel servicing, fuels laboratory
🗑
|
||||
| Who is responsible for making the initial notification to predetermined support agencies of adverse weather conditions? | Base weather station
🗑
|
||||
| Refueling vehicles should not be parked within how many feet of inhabited buildings? | 100ft
🗑
|
||||
| Fuel servicing Safety Zone is an area within_____feet of a pressurized fuel carrying servicing component, and_____ feet around aircraft fuel vent outlets? | 50ft; 25ft
🗑
|
||||
| When will fueling/de-fueling operations cease? | Aircraft being serviced is in the beam of high-powered radar, the radio on the aircraft is in operation, if a spill/leak develops, or aircraft engine running intrudes.
🗑
|
||||
| Fuel servicing will not commence when lighting is within how many nautical miles? | 5nm
🗑
|
||||
| The maximum quantity of test fuel in the lab will be how many gallons? | 10gal
🗑
|
||||
| All lab equipment will be_____when in use? | Grounded and Bonded
🗑
|
||||
| In addition to AFOSH, hospitals are required to be in compliance with: | Pertinent federal regulations, consensus standards, centers for disease control, EPA, and JCAHO
🗑
|
||||
| A failure of a JCAHO inspection can mean a loss of what? | Accreditation
🗑
|
||||
| The assigned qualified safety person or the appointed safety monitor will be responsible for the internal hospital safety program is who? | Plant manager
🗑
|
||||
| Which type of extension cords are prohibited in any patient care areas? | TWO-wire cords
🗑
|
||||
| Who will receive job safety training? | All personnel
🗑
|
||||
| “Wet areas” will be equipped with what? | GFCI’s
🗑
|
||||
| Supervisors will ensure all machines are given a thorough inspection at least every_____days? | 60 days
🗑
|
||||
| Walk in refrigerators/cold storerooms must be equipped with at least_____door that can be opened from_____. | One door; from the inside
🗑
|
||||
| A confined space is a space that: | Large enough for a worker to enter and work, limited entry and exit, is not designed for continuous human occupancy.
🗑
|
||||
| Who assists the functional managers and commanders in developing and administering confinded space programs? | Confined Space Program Team (CSPT)
🗑
|
||||
| Who coordinates the installation confined space program? | Chief of Ground Safety
🗑
|
||||
| Who leads the installation Confined Space Program Team? | Chief of Ground Safety
🗑
|
||||
| Who provides rescue support for confined space entries according to local agreements? | Installation Fire Chief
🗑
|
||||
| Who ensures a written confined space program is developed? | Commanders/functional managers
🗑
|
||||
| Who serves as a member or designates a representative to the CSPT for management of confined spaces within the functional manager’s control and assist in the development of the MEPs? | Commanders/functional managers
🗑
|
||||
| Maintain the organizational MEP, issues entry permits consistent with the MEP, and revokes the permit and contacts SEG when any entry conditions are not consistent with the MEP? | Entry supervisor
🗑
|
||||
| Who maintains an accurate accounting of entrants in the permit space? | Confined space attendants
🗑
|
||||
| Entry supervisors will ensure workers enter a permit-required confined space ONLY after an AF IMT_____or an approved entry permit which contains the minimum requirements of the AF permit has been obtained. | AF IMT 1024
🗑
|
||||
| All master entry plans shall be reviewed by the organizational representative at least how often? | Annually
🗑
|
||||
| Non-permit confined spaces shall be reviewed at least_____,to ensure conditions have not changed which could result in a potential for hazards and a change in confined space classification | Annually
🗑
|
||||
| In what sequence will atmospheric testing be performed? | OFTEN: Oxygen, Flammable, Toxic
🗑
|
||||
| What is the preferred method of rescue? | Self-rescue
🗑
|
||||
| Whenever workers will perform hot riveting, welding, cutting or burning, or heating operations within a confined space, they will obtain what form from the Fire Dept? | AF IMT 592
🗑
|
||||
| What is the preferred method to control the accidental release of stored energy from equipment? | Lockout/ Tagout
🗑
|
||||
| LO/TO procedures shall only be performed by whom? | Certified supervisors and operators
🗑
|
||||
| Where a lock cannot be used due to design of equipment, tags with a minimum of how many pounds of unlocking strength shall be attached? | 50 lbs
🗑
|
||||
| Training will be certified and documented, will be kept up to date, and documented on which AF Form? | Form 55
🗑
|
||||
| When does LO/TO retraining occur? | Annually or a change in the job, equipment or LO/TO procedures
🗑
|
||||
| LO/TO program inspection will be conducted at least_____by_____. | Annually by SEG
🗑
|
||||
| A documented,__self inspection will be conducted by the__ to ensure comp. with all program elements and will include the ID of machines and equip. and a review of each person’s resp. ensuring all necessary training has been conducted and documented. | Periodic; unit
🗑
|
||||
| Substances, mistures, or compounds are categorized as either: | Corrosives, explosives, flammables, or toxic
🗑
|
||||
| Explosives are: | substances, mixtures, or compounds that can enter into a combustion reaction so rapidly and violently that they can cause an explosion
🗑
|
||||
| Corrosives can destroy: | living tissue
🗑
|
||||
| Flammable liquids are those liquids with a flash point of: | below 100F
🗑
|
||||
| Combustible liquids are those with a flash point of: | 100F or above
🗑
|
||||
| What are the different modes of entry into the body? | Ingestion, Absorption, Inhalation, and Injection
🗑
|
||||
| The two major causes of occupation dermatitis are: | predisposing and direct
🗑
|
||||
| Threshold Limit Value is: | A time weighted average concentration under which most people can work consistently for 8 hours a day, day after day, with no harmful effects.
🗑
|
||||
| Threshold Limit Value-Time Weighted Average is: | the time weighted average concentration for a normal 8-hour day or 40-hour workweek to which nearly all workers may be repeatedly exposed without adverse reaction or effect (8/40)
🗑
|
||||
| Threshold Limit Value-Short Term Exposure Limit is: | the maximum concentration to which workers can be exposed for up to 15 minutes continuously (4 times in one 8 hour day- must be at least 60 minutes between exposures)
🗑
|
||||
| Threshold Limit Value-Ceiling is: | the concentration level that should never be exceeded at any time
🗑
|
||||
| Locations are divided into ____ and ____. | Classes and divisions
🗑
|
||||
| Division 1 locations are designated as such because: | a flammable gas, vapor, dust, or easily ignitable material is normally present in hazardous quantities
🗑
|
||||
| Division 2 locations are designated as such because: | the existence of hazardous quantities of these materials is not normal but they occasionally exist, either accidentally or when material in a storage is handled
🗑
|
||||
| Who must develop fire prevention regulations to meet their specific needs? | Each base
🗑
|
||||
| There are four classifications of fires; what are they? | Class A-involves wood, paper, and/or rags Class B-involves flammable liquids/vapors,ect. Class C-involves electrical equipment (energized) Class D-involves combustible metals
🗑
|
||||
| True/False Signs are intended for use as a management control of hazards and can be used as a substitution for safe work practices. | False
🗑
|
||||
| Green signifies what? | Safety & first aid equipment
🗑
|
||||
| Red signifies what? | Fire prevention equipment/danger and/or stop
🗑
|
||||
| Standard coloring of piping reduces what? | The chance of error in identification by workers
🗑
|
||||
| Bands should completely encircle the pipe and may be _______ inches wide. | 8 to 32 in.
🗑
|
||||
| Operators will be trained in: | The proper operation, safety procedures, cleaning, hazard recognition, and emergency shutdown procedures for each machine or piece of equipment they are to use
🗑
|
||||
| Supervisors and operators will receive training on: | LO/TO procedures
🗑
|
||||
| What type of guard may be moved or reconfigured to allow for different types of production, such as different sizes of stock or raw materials? | Adjustable guard
🗑
|
||||
| Who is responsible for the procurement of the proper types of guarding and for ensuring the proper guarding is in place for each piece of machinery? | Management
🗑
|
||||
| Operator’s inspection shall be conducted when? | Prior to the start of each shift, following a new setup, or when operators change
🗑
|
||||
| When work is performed from the scaffold, what shall be secured? | Footing and anchorage
🗑
|
||||
| Scaffolds and their components will be capable of supporting at least how many times the maximum intended load? | 4 times
🗑
|
||||
| Scaffold guarding will consist of the following parts: | A guardrail of 2-by 4-inch lumber or equivalent material installed at as height of 36 to 42 inches above the platform
🗑
|
||||
| What is the primary hazard associated with the use of portable ladders? | Falls
🗑
|
||||
| Extra heavy duty IA = | 300lbs
🗑
|
||||
| Heavy duty 1= | 250lbs
🗑
|
||||
| Medium duty II= | 225lbs
🗑
|
||||
| Light duty III= | 200lbs
🗑
|
||||
| Which type of ladder should not be procured for industrial use? | TypeIII, light duty
🗑
|
||||
| Metal and metal-reinforced ladders used for electrical hazards shall be marked with: | “Danger—do not use around electrical equipment”
🗑
|
||||
| Place straight and extension-type ladders in a position to have at least _____ foot of slope for each _____ foot of ladder length. | 1ft slope; 4ft of ladder length
🗑
|
||||
| A formal, full documented inspection of all fixed ladders will be accomplished upon installation and at least every _____ years thereafter. | 3yrs
🗑
|
||||
| What are three common methods of protection for those who work in excavation and trenching? | Shoring, sloping, and benching
🗑
|
||||
| True/False Dirt bands 5 feet or more in depth require worker protection. | True
🗑
|
||||
| Tools, equipment, and excavated material will be kept _____ or more from the lip of the trench. | 2ft
🗑
|
||||
| Workers within trenches must have an adequate means of exit and should not have to travel more than ______ of travel. | 25ft
🗑
|
||||
| Inspections of lifting devices must be accomplished how often? | Daily, before each use & annually
🗑
|
||||
| In addition to initial training and certification, a qualified instructor shall evaluate each operator at least once every _____ years and provide refresher training in relevant topics anytime there is reason to believe there is a need. | 3yrs
🗑
|
||||
| Forks will not be elevated more than _____ above the ground surface. | 6 in.
🗑
|
||||
| OSHA defines ergonomics as: | Designing the job to fit the worker
🗑
|
||||
| What are the goals of ergonomics? | Increased productivity, safety, health, and job satisfaction
🗑
|
||||
| Ergonomic factors include: | Environmental and physical
🗑
|
||||
| Sprains account for approximately _____ of the lost time injuries in the Air Force. | 30%
🗑
|
||||
| Who must train personnel who regularly perform manual lifting duties? | Supervisors
🗑
|
||||
| Training will be documented IAW which AFI? | AFI 91-301
🗑
|
||||
| There are three basic methods of lifting. What are they? | Strait back bent knees Freestyle Kinetic
🗑
|
||||
| When must personnel perform equipment inspections? | Prior to each use and daily
🗑
|
||||
| A comprehensive training plan must be established and the training must be documented. Where can training be annotated? | AF For 55’s or 623’s
🗑
|
||||
| What type of equipment will be used indoors, ideally? | Electric or battery powered
🗑
|
||||
| Whenever it becomes necessary to perform required tasks where a worker can fall __________, fall protection will be used. | 4 ft. or more
🗑
|
||||
| The two common systems for fall protection are: | Fall arrest and fall restraint
🗑
|
||||
| Anchorage for lanyards that tie off one worker will be capable of supporting at least how many pounds? | 5000
🗑
|
||||
| Lanyards, D-rings, locking snap-hooks, and all components of a fall arrest system will also be capable of sustaining a minimum tensile load of _____ pounds. | 5000
🗑
|
||||
| Who acts as the central focal point and local expert on matters relating to RFR hazards and bio-effects? | BE
🗑
|
||||
| Who will investigate all alleged or suspected overexposure? | BE
🗑
|
||||
| Who will work closely with BE in investigating RFR incidents and provide medical surveillance feedback to BE? | Public Health
🗑
|
||||
| Who will prepare and distribute AF Form 190 for all incidents of alleged personnel overexposure to RFR? | Public Health
🗑
|
||||
| Whose responsibility is it to provide and document initial and refresher training to all personnel? | Supervisors
🗑
|
||||
| Who should review unit RFR safety training materials and attendance records during their annual industrial hygiene visits? | BE
🗑
|
||||
| Who is the program facilitator for Laser safety program? | BE
🗑
|
||||
| What are the classifications for lasers? | 1-Non-hazardous 2-Visible Laser; Aversion Response will protect 3a-Eye hazard with optical aides 3b-Eye hazard, some skin at high power 4-Eye hazard, skin hazard, fire hazard, diffuse reflection hazard
🗑
|
||||
| What is the main organ of concern? | The eye
🗑
|
||||
| Upon notification of a suspected exposure, who will promptly investigate the incident or accident? | BE
🗑
|
||||
| Who is required to establish a written Exposure Control Plan designed to eliminate or minimize employee exposure? | Each Employer
🗑
|
||||
| The Exposure Control Plan shall be reviewed and updated at least ______ and whenever necessary to reflect new or modified tasks and procedures which affect occupation al exposure and to reflect new or revised employee positions with occupational exposure. | Annually
🗑
|
Review the information in the table. When you are ready to quiz yourself you can hide individual columns or the entire table. Then you can click on the empty cells to reveal the answer. Try to recall what will be displayed before clicking the empty cell.
To hide a column, click on the column name.
To hide the entire table, click on the "Hide All" button.
You may also shuffle the rows of the table by clicking on the "Shuffle" button.
Or sort by any of the columns using the down arrow next to any column heading.
If you know all the data on any row, you can temporarily remove it by tapping the trash can to the right of the row.
To hide a column, click on the column name.
To hide the entire table, click on the "Hide All" button.
You may also shuffle the rows of the table by clicking on the "Shuffle" button.
Or sort by any of the columns using the down arrow next to any column heading.
If you know all the data on any row, you can temporarily remove it by tapping the trash can to the right of the row.
Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.
Normal Size Small Size show me how
Normal Size Small Size show me how
Created by:
SEG
Popular Miscellaneous sets