Physics 2 final Word Scramble
|
Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.
Normal Size Small Size show me how
Normal Size Small Size show me how
Question | Answer |
State the maximum permissible tube leakage. | Less than 100 mR/hr @ 1 meter at maximum when operating at capacity and at 2 meters should be less than 25 mR |
Give the primary and secondary purpose of the oil that surrounds the tube | Reduces electric shock, electrical insulation and heat dissipation |
Explain what is meant by thermionic emissions | When filament is heated enough, ion production begins the boiling off of electrons (the creation of ions through heat) |
State the temperature required for thermionic emission with a tungsten filament | 2200 degrees C |
Recognize the melting point of tungsten | 3410 degrees C |
List the materials used in a tungsten filament | Thoriated tungsten (tungsten with thorium) |
Name the materials used in a focusing cup | Nickel with rhenium |
Compare the benefit of a smaller focal spot to the benefit of a larger focal spot | Small has more detail (greater spatial resolution) from 0.1-1mm and large has greater heat capacity (mA) from 0.3-2mm |
Compare the production of heat to the production of x-rays in the x-ray tube | 99% heat and 1% x-ray |
Compare the speeds of a normal rotating anode with a high speed anode | Normal is 3400 rpm and high speed is 10,000 rpm |
Name the device that is used to enable a rotating anode to rotate | Induction motor |
Explain what the stator is and where it is located | Part of the induction motor series of fixed electromagnets in stationary coil windings located in the protective housing but outside the x-ray tube glass envelope at the anode end of tube |
Explain what the rotor is and where it is located | Rotating part of an electromagnetic induction motor located inside the glass envelope at the anode side of tube |
Explain the line focus principle and how it is used in the design of an x-ray tube | Design incorporated into x-ray tube targets allows a large area for heating while a small focal spot is maintained by angling the anode (EFS size much less than AFS) |
Actual focal spot size | area on the anode target that is exposed to electrons from the tube current |
Effective focal spot size | area projected onto the patient and the image receptor |
Compare the actual focal spot size to the effective focal spot size | AFS – area struck by electron beam. EFS – area from IR perspective by angling of the anode (AFS always larger than EFS) |
Compare relationship between anode angle and effective focal spot size | As anode angle increases the effective focal spot will increase (never angle more than 45 EFS would actually be greater than AFSNO BENEFIT) the greater the angle the greater the EFS |
State what happens to anode heat capacity as anode angle increases | As anode angle increases so does anode heat capacity |
State what happens to field coverage as anode angle increases | As anode angle increases field coverage increases |
State what happens to resolution as anode angle increases | Spatial resolution decreases as anode angle increases |
Heel effect | absorption of x-rays in the heel of the target resulting in reduced x-ray intensity to the anode side of the central axis. The smaller the anode angle the larger the heel effect |
Explain how to use the anode heel effect to improve image quality | Image quality improves with anode directed over smaller area cathode over thicker side FAT CAT |
Compare resolution on the anode side of the tube to the cathode side of the tube | Spatial resolution greater on anode side with more focal spot blur (less resolution) on cathode side |
State the effect SID has upon the anode heel effect | As SID increases anode heel effect decreases (divergence of beam?) |
State the effect field size has upon anode heel effect | Smaller field size decreases heel effect (from last test larger IR better than smaller IR- more scatter more density) |
State the effect anode angle has upon the anode heel effect | As anode angle increases anode heel effect decreases |
Explain what is meant by extra focal or off-focus radiation | X-rays produced at the anode but not at the focal spot. Electrons bounce off the focal spot and land on other areas of the target |
List three ways in which heat is dissipated in an x-ray tube | Radiation, conduction and convection |
Read a tube rating chart and determine whether an exposure is safe | Common sense- if mA + kVp + time is higher than the line it is an unsafe exposure under the line is safe |
Calculate heat units produced in a single phase x-ray machine when given a technique | HU = mA x time in seconds x kVp |
Calculate the heat units produced in a three phase 12-pulse x-ray machine when given a technique | HU = mA x time in seconds x kVp x 1.41 (for one exposure!) for multiple exposures you have to multiply by the number of exposures |
Read an anode cooling chart or housing cooling chart to determine the exposure capacity of an x-ray tube | Exposure capacity - divide capacity by total exposures made (total exposure capacity and divide by total exposures (HU) made) heat capacity divided by heat units per exposure |
State two types of interactions that produce diagnostic x-rays | Characteristic and Brems |
State which of these two is an ionizing event | Characteristic |
Explain how a characteristic interaction produces x-radiation | X-rays after ionization (projectile electron removes an inner shell electron) of a K-shell electron. When an outer-shell electron fills the vacancy in the K-shell results in an x-ray emitted. |
Explain how a Bremsstrahlung radiation is produced | Result from interaction between a projectile electron and a target nucleus. The electron is slowed, its direction is changed and leaves with reduced kinetic energy. This loss of kinetic energy reappears as an x-ray. Can have energy up to 70 kVp |
State the relationship between x-ray energy and wavelength | Inversely proportional- as x-ray energy increases wavelength decreases (gets smaller) |
Explain how changes in mAs affect x-ray beam quantity and quality | mAs changes beam quantity does NOT change quality |
Explain how changes in kVp affect x-ray beam quantity and quality | Increasing kVp increases quantity and quality (and vice versa) |
Explain how changes in filtration affect x-ray beam quantity and quality | As filtration increases quantity decreases and quality increases |
Explain how changes in target Z number affect x-ray beam quantity and quality | Target Z number increases beam quantity and quality increases |
Explain how changes in generator power (voltage waveform/ripple) affect x-ray beam quantity and quality | As generator power increases (voltage waveform/ripple decreases), beam quality increases and quantity increases |
List three terms that can be used to refer to the number of photons in the x-ray beam | Quantity, exposure and intensity |
List two major units used to measure radiation exposure (measure of beam) | mR and Graya (milliroentgens or gray in air |
Explain relationship between x-ray quantity and radiographic density | X-ray quantity and radiographic density are directly proportional |
Explain relationship between x-ray quantity and patient dose | X-ray quantity increases patient dose increases |
List four major factors affecting x-ray quantity | mAs, kVp, distance and filtration |
State the relationship between mAs and x-ray intensity | Directly proportional (mA is a measure of tube current-what is traveling across the tube not x-rays) |
Calculate the changes in x-ray intensity when a specific numeric change is made to the mAs of the beam | Double the mAs double the x-ray intensity |
State the relationship between kVp and x-ray intensity | kVp increases intensity increases (double the kVp and 4x the intensity) |
State the inverse square law | The intensity of the radiation at a location is inversely proportional to the square of its distance from the source of radiation |
Use the inverse square law to calculate the change in radiation exposure as distance from the source changes (apply) | I1÷I2 = (D2÷D1)2 |
Calculate what change is needed in radiation exposure as distance from the source changes | Density maintenance law or Square law: compensate for a change in SID by changing mAs by the factor SID2 [mAs1÷ mAs2 = (SID1÷SID2)2] |
Explain the relationship between filtration and patient dose | As filtration increases patient dose decreases |
Explain the relationship between x-ray beam energy and penetrability | As energy increases penetrability increases |
Explain what is meant by quality of the beam | Quality is the penetrability of the beam. (increase quality = increased penetrability) |
State how the quality of an x-ray beam is measured | HVL |
Explain the relationship between HVL and beam penetrability | HVL is a measurement of beam quality. As HVL increases beam penetrability increases. |
State the effect increasing SID will have upon beam quantity (intensity) | Increase in SID will decrease beam intensity (quantity) |
State the effect increasing SID will have on beam quality | SID has no effect on beam quality |
State what happens to the HVL of a beam as the energy of a beam increases | HVL increases as beam energy increases |
State why we wish to reduce the number of low energy photons in the x-ray beam | To decrease patient dose (skin dose) |
Define a compensating filter | Used to give a better image for part thickness (more uniform) EX: trough-chest, “bow-tie”-Computed Tomography, wedge-foot Used to give a better image for part thickness (more uniform) EX: trough-chest, “bow-tie”-Computed Tomography, wedge-foot |
State what three factors determine the probability of an x-ray interaction with matter | Energy of the beam, mass density, subject atomic number (Z number) |
Name two interactions that are significant in the production of diagnostic radiographs | Photoelectric and Compton |
Recognize the three other names for coherent scatter | Classical, Rayleigh, Thompson |
Describe what happens during a coherent scattering event | Incident x-ray interacts with a target atom, disappears, causing atom to become excited. The target atom immediately releases this excess energy as a scattered x-ray with a wavelength equal to that of the incident x-ray (almost instantaneously) |
Compare the energy and direction of the incident photon and the scattered photon of a coherent scattering interaction | Incident photon and scattered photon have same amount of energy. Direction of the scattered x-ray is different from that of the incident x-ray |
Describe what happens during a Compton scattering event | The incident photon interacts with an outer-shell electron and ejects it from the atom, thereby ionizing the atom. The x-ray continues in a different direction with less energy |
Compare the energy and direction of the incident photon to the energy and direction of a Compton scattered x-ray | Photon has a change of direction and a loss of energy |
State what happens to a Compton electron | Compton electron comes out of its shell and goes on its own way (usually somewhere in the body) |
Explain what happens to the probability of a Compton interaction occurring as the energy of the incident photon increases | As incident photon energy increases a decrease in Compton interactions |
Explain what happens to the probability of a Compton interaction occurring as the atomic number of the subject atom increases | As atomic number of subject atoms increases NO CHANGE in probability of Compton |
Explain what happens to the probability of a Compton interaction occurring as the mass density of subject atom increases | Increases proportionately – DOUBLE the MATTER = DOUBLE the SCATTER!!!! |
State the effect Compton scatter has upon radiographic contrast | Radiographic contrast decreases as Compton scatter increases |
State the effect Compton scatter has upon radiographic density | Radiographic density increases as Compton scatter increases |
Describe what happens during a photoelectric interaction | Ionizing interaction with inner-shell electrons. Incident x-ray is totally absorbed during ionization of an inner-shell electron. The incident photon disappears, and the K-shell electron (now a photoelectron) is ejected from the atom |
Describe what happens to the incident photon | Incident photon disappears - is absorbed |
Compare photoelectric interaction with a characteristic interaction | Characteristic is because of an electron and a photoelectron is because of a photon |
Explain what happens to the probability of a photoelectric interaction occurring as the energy of the incident photon increases | As the energy of the incident photon increases less chance of a photoelectric interaction |
Explain what happens to the probability of a photoelectric interaction occurring as the subject atomic number of the subject atom increases | As subject atomic number increases photoelectric interaction increases dramatically (X3) |
Explain what happens to the probability of a photoelectric interaction occurring as the mass density of the subject atom increases | As mass density increases the probability of photoelectric interaction increases |
Explain what happens during a pair production event | High energy x-ray photon (greater than 1.02MeV) interacts with nuclear force field and its energy is converted into two particles that have opposite electrostatic charges are created. (positron and electron) |
State how much energy is required for a pair production event to occur | 1.02MeV (0.51 MeV is mass equivalence of an electron) |
Explain what happens during a photodisintegration event to occur | Photon absorbed directly by nucleus, nucleus is raised to an excited state and instantly emits a nucleon or other nuclear fragment |
State how much energy is required for a photodisintegration event to occur | 10 MeV |
Define radiopaque | Substance that absorbs x-rays (appears white on an x-ray) |
Define radiolucent | Substance that easily transmits x-rays (black/dark on an x-ray) |
Compare the changes in probability of a photoelectric interaction occurring to the probability of a Compton interaction occurring as x-ray energy increases | Both decrease as energy increases but a HUGE decrease in photoelectric (X3) compared to decrease in Compton |
Compare changes in probability of a photoelectric interaction occurring to the probability of a Compton interaction occurring as subject matter atomic number increases | Compton there is no effect and photoelectric increases greatly |
Compare changes in probability of a photoelectric interaction occurring to the probability of a Compton interaction occurring as subject mass density increases | Both will increase proportionately |
Give an example of a negative contrast material | Air (increases transmission of x-rays) |
List which of the five interactions are ionizing events | Compton & photoelectric |
Give the reaction that contributes greatest to technologist radiation dose | Compton |
Give the interaction that contributes greatest to patient dose | Photoelectric |
State the interaction that is the major cause of film fog | Compton |
Differentiate between spatial resolution and contrast resolution | Spatial – differentiate by sizeContrast – differentiate between tissue (shades) |
Define quantum mottle | Result of random nature of interaction with IR – not enough signal – photon starved |
Tell how quantum mottle can be reduced | Increase number of x-rays High mAs, low kVp and slower image receptors will reduce quantum mottle (decrease in mA increases quantum mottle) |
Distinguish between a densitometer and a sensitometer | Densitometer measures the optical density of exposed filmSensitometer creates an optical step wedge electronically which is used to construct characteristic curve |
State the change doubling exposure to a film will have upon optical density | Optical density will increase by 0.3 (LOG of 2 = 0.3) |
Tell what the law of reciprocity states | Optical density is proportional to how much energy reaches the film (mAs=mAs) |
Define radiographic contrast | Differences in optical density |
Compare terms: High contrast & Low contrast | black and white (big differences) & many shades of gray (small differences) |
Compare terms:Long scale & Short scale | low-contrast radiograph that has many shades of gray & high contrast radiograph that has few shades of gray |
Compare terms:High kVp & Low kVp | low contrast & high contrast |
Compare several characteristic cures and state which curve demonstrates the greatest or least contrast | More vertical – more contrast, more speed – closest to y-axis, less latitudeMore horizontal – less contrast, less speed – farther from y-axis, more latitude |
Calculate the new mAs required when a change in IR speed is made | New IR speed ÷ old IR speed = old mAs ÷ new mAs (inversely proportional) |
Define radiographic latitude | Range of exposure that will produce a diagnostically acceptable radiograph |
State the effect developer time has on contrast, speed and fog | Increase developer time – contrast decreases and speed and fog increases |
State the effect developer temperature has on contrast, speed and fog | As temperature increases – contrast decreases and speed and fog increases |
List the three geometric factors of radiographic quality | Distortion, magnification and blur |
Calculate on object size when given an image size, SID and OID | Object size = image size (SOD ÷ SID) or image size ÷ object size = SID ÷ SOD |
Explain how to minimize magnification | Large SID and small OID |
Give the situation which will cause elongation | Tube or IR angulation |
Give the situation which will cause foreshortening | Part misalignment |
Define focal spot blur | Softening of the edges of structure on an image caused by the size of the focal spot (blurred region of radiograph) |
Calculate focal spot blur when given focal spot size, SID and OID | Focal spot blur = effective focal spot x (OID ÷ SOD) |
focal spot size and magnification? | Focal spot size has no effect on magnification |
Large focal spot will have more or less focal spot blur? | Large focal will have less softening (focal spot blur) |
Explain the relationship between kilovoltage, contrast and latitude | Kilovoltage increases contrast decreases and latitude increases (wide) and vice versa |
State the best way to reduce voluntary motion | Good patient instruction |
Explain the best way to reduce involuntary motion | Short exposure time |
State the relationship between image receptor speed and patient dose | As image receptor speed increases patient dose decreases |
Explain the relationship between kilovoltage, contrast and latitude | Kilovoltage increases contrast decreases and latitude increases (wide) and vice versa |
State the best way to reduce voluntary motion | Good patient instruction |
Explain the best way to reduce involuntary motion | Short exposure time |
State the relationship between image receptor speed and patient dose | As image receptor speed increases patient dose decreases |
Created by:
hapyday37
Popular Physics sets