| Question | Answer |
| Which frame relay DLCIs are reserved? | 0-15 and 1008-1023 |
| How does the router know what LMI type to use? | auto-sense by trying each one |
| What three LMI options are there? | Cisco, ANSI, Q.933 - Annex A |
| What does the LMI status ACTIVE mean? | Healthy on each end and data can be transferred |
| What does the LMI status INACTIVE mean? | local connection is healthy, but the remote side is not |
| What does the LMI status DELETED mean? | No LMI, or the DLCI was deleted from the SP Frame-Relay switch |
| What is the full mesh formula? | [n(n-1)]/2 |
| Why was Phase II of DMVPN created? | to permit the dynamic creation of spoke-to-spoke tunnels |
| What 3 technologies is used by DMVPN? | IPSec, Multipoint GRE (mGRE), and Next Hop Resolution Protocol (NHRP) |
| This DMVPN technology is used to dynamically register addresses from the spokes | Next Hop Resolution Protocol (NHRP) |
| This DMVPN technology is used to transport data and routing information from the hub to multiple (potential) spokes | mGRE |
| Command to create DMVPN mGRE tunnel? | tunnel mode gre multipoint |
| Commands to configure the two phases of IPSec | crypto isakmp policy and crypto ipsec transform |
| Command to create an IPSec profile to | crypto ipsec profile |
| What is the typical size of a Frame Relay DLCI header? | 10 bits |
| When a FR switch notices congestion, what first action will it take? | Set FECN bit for router receiving the data. |
| What devices can set the FECN bit? | Frame Relay switches only |
| How does the Frame Relay switch notify the sending router that it needs to lower it's shaping rate? | Setting the BECN bit |
| What devices can set the BECN bit? | |
| When a FR switch notices congestion, what action can it take immediately aside from setting the FECN or BECN bit on DTE forwarded traffic? | Generate a Q.922 test frame with the BECN set |
| What LMI message can DTE send to the FR switch? | LMI Status Enquiry |
| What type of message does the FR Switch reply with when it receives an LMI message from the DTE? | LMI Status |
| How often are LMI keepalive messages sent? | Every 10 seconds |
| When not inquired, when are full status LMI messages sent? | Every 6th LMI message |
| What DLCI does Cisco LMI use for operation? Assignable DLCI range? | 1023, 16-1007 |
| What DLCI does Anis LMI use for operation? Assignable DLCI range? | 0, 16-991 |
| What DLCI does Q.933 Annex A LMI use for operation? Assignable DLCI range? | 0, 16-991 |
| The FR LAPF contains a header and a trailer. What is the FR LAPF header used for? What information does the header contain? | Used by FR Switches in FR cloud; DLCI, FECN BECN, DE |
| What does the FR encapsulation header contain? What is it used for? | Contains a protocol type field. It is used for DTE to DTE multiple Layer3 support |
| What two FR encapsulation options are there? | Cisco, IETF |
| What three options are the for FR Payload compression? | Packet-by-packet, data stream, and FRF.9 |
| What algorithm is used by the FR payload compression options? | LZS |
| What two methods are there for FRF.12 fragmentation implementation? | Legacy (uses map-class), Interface |
| What 3 options are there for FR fragmentation? | FRF.12, FRF.11-c, Frame-Relay LFI with MLP |
| What is FRF.11-c used for? | VoFR |
| In FRF.11-c, voice frames are always ___________, but never __________. | interleaved, fragmented |
| Which Frame Relay fragmentation method uses PPP, Multilink, and a virtual template? | Frame-Relay LFI with MLP |
| What does Cisco's version of HDLC add to the standard? What does this addition contain? | 2 byte Type field, Protocol field and padding field |
| What two categories make up the PPP standards? | Layer 3 unrelated features (LCP), Layer 3 specific features (NCP) |
| Link Quality Monitoring (LQM), Looped link detection, Layer 2 load balancing, and Authentication are an example of what PPP category? | LCP |
| IPCP and CCP are examples of what PPP category? | NCP |
| How does Link Quality Monitoring work in PPP? | Routers exchange stats about error-free frame percentage, link dropped if level falls below configured value |
| How does Looped link detection work in PPP? | "Routers generate and send random ""Magic Number,"" if it receives its own, brings link down" |
| How are frames sent over PPP Multilink interfaces? | Frames fragmented into one fragment per link or based on fragmentation delay |
| What does MLP add to each fragment for reassembly? | Headers (2 or 4 bytes), contains sequence number field and flab bits designated beginning and end |
| What two interface types can PPP multilink use? | Multilink, Virtual-Templates |
| How is the ppp multilink fragment-delay measured? | milliseconds |
| What determines which fragmented packet to send with ppp multilink? | Queuing scheduler on multilink |
| What compression types can PPP negotiate? | Layer 2 payload, IP/TCP header, IP/UDP/RTP header |
| What three options are there for PPP Layer 2 payload compression? | Lempel-Ziv Stacker (LZS), Microsoft Point-to-Point Compression (MPCC), Predictor |
| What Layer interface must be used for Layer 2 payload compression with ATM-to-Frame Relay Service? | MLP |
| What PPP Layer 2 payload option is supported on both Frame-Relay and HDLC links? | Lempel-Ziv Stacker (LZS) |
| What is the normal efficiency of PPP IP/TCP header compression? | 40 bytes to 3 or 5 bytes |
| What is the normal efficiency of PPP IP/UDP/TCP header compression? | 40 bytes to 2 or 4 bytes |
| What two configuration options are there for PPP header compression? | Legacy (configured on ppp serial link or multilink), MQC |
Embed Code - If you would like this activity on your web page, copy the script below and paste it into your web page.
Normal Size Small Size show me how
Normal Size Small Size show me how
Created by:
ajballer15
on 2011-08-13